Hitachi H8S/2376 F-ZTAT Hardware Manual Download | Manualshive

Page: 737 / 949

background image

Rev. 1.0, 09/01, page 693 of 904

Initialization

Read RDR and clear

RDRF flag in SSR to 0

Clear RE bit to 0

Start reception

Start

Error processing

No

No

No

Yes

Yes

ORER = 0 and

PER = 0

RDRF = 1?

All data received?

Yes

Figure 15.30 Example of Reception Processing Flow

15.7.8

Clock Output Control

When the GM bit in SMR is set to 1, the clock output level can be fixed with bits CKE1 and
CKE0 in SCR. At this time, the minimum clock pulse width can be made the specified width.

Figure 15.31 shows the timing for fixing the clock output level. In this example, GM is set to 1,
CKE1 is cleared to 0, and the CKE0 bit is controlled.

Specified pulse width

SCK

CKE0

Specified pulse width

Figure 15.31 Timing for Fixing Clock Output Level

«
...
735
736
737
738
739
...
»

Summary of Contents for H8S/2376 F-ZTAT






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2376 F-ZTAT

Brand: Magnat Audio Pages: 2

Brand: Paradyne Pages: 20

Compshere 3000 Series

Brand: Paradyne Pages: 2

Brand: Cypress Semiconductor Pages: 9

Brand: FOR-A Pages: 39

TeleCLIENT TC7730 Series

Brand: ETL Pages: 83

Compact NVR-AS 4000

Brand: IndigoVision Pages: 38

Brand: ZyXEL Communications Pages: 3

Brand: ivideon Pages: 11

Brand: ETAS Pages: 84

Brand: Xtreme Pages: 83

Brand: MCT Pages: 12

Brand: CyberResearch Pages: 59

ExtremeCloud Appliance E1120

Brand: Extreme Networks Pages: 219

Brand: Dinstar Pages: 103

Brand: Xtreme Pages: 83

Brand: National Instruments Pages: 35

PMP/PTP 450 Series

Brand: Cambium Networks Pages: 155

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands