217
Regelung der +8/ +5v Schienen durch (?). Die Ausgangsimpulsbreite verändert sich mit der Last, um die korrekte Regelspannung
beizubehalten.
Die Ausgabe von I910 Stift 1,7 wird durch ein Gegentakt-Transistorennetzwerk Q929, Q917 (für +5V) gepuffert, um die
Schaltverlustleistung zu verbessern. Dieses Transistorennetzwerk bringt schnelle Flanken-Schaltung von Q912 (+5) und Q911
(+8V). Schutz vor Überlaststrom wird durch den Stromfühlungswiderstand RP03 geboten. Netzwerk Q956 RP04/C966 zieht Stift 10
von I903 hoch, wenn Hochlaststrom durch RP03 fließt.
Wicklung 2/11 produziert ca. 16V über D952, was von C955 abgeglichen und dann auf Q921 angewandt wird über R974, der als
Stromfühlung benutzt wird. Der Ausgang von Q921 liefert 16V für Audio-Verstärker I401.
Die Hochspannungsregelung wird durch die Q954 Stufe gesteuert. Die Basis von Q954 wird vom Widerstandnetzwerk R950, R982
und R953 auf einen vorbestimmten Pegel eingestellt. Der Emitter von Q954 wird durch Z950 auf ca. 6V2 gehalten. Sollte die
Hochspannung steigen, wird die Basisspannung positiver als der Emitter, und diese Differenz wird durch den Transistor verstärkt
und auf den Optokuppler I901 angewandt. Die Ausgabe von I901 wird dann auf Stift 1 von I900 angewandt, der die Hochspannung
regelt, indem er den Arbeitszyklus der Wellenformausgabe von Stift 6 von I900 ändert.
BEREITSCHAFTS-SCHALTUNG
Die Niederspannungsversorgung ist in Bereitschaft ausgeschaltet, dies wird durch den Mikroprozessor gesteuert, der im
Bereitschaftszustand ein Hoch ausgibt und ein Tief, wenn das Gerät nicht im Bereitschaftszustand ist. Dies wird dann auf die
Widerstände R923 und R940/R977 angewandt. Dieses ‘Hoch’ wird auch auf die Basen von Q915, Q916, Q910 angewandt, die
ihrerseits den Betrieb der +8, +5 Gleichstromwandler beenden und das Gate von Q921 tief ziehen und somit die +16V Audio-
Stromversorgung in den niederen Bereich schalten. In Bereitschaft steigt die +B Spannung leicht, um die Spannung der
Vorspannungs-Wicklung für Stift 7 von I900 zu erhalten. Um das Gerät aus der Bereitschaft zu schalten, schaltet der
Mikroprozessor die Ein-Aus-Leitung hoch, und Q916, Q915, Q910 werden deaktiviert, wodurch die +8, +5, +16V Schienen zum
normalen Betrieb zurückkehren.
MINUSPOL DER STROMVERSORGUNG UND SCHUTZ
I903 besteht aus 4 Komparatoren, der Minuspol der Stromversorgung benutzt Komparator 2. Stift 5 wird als Bezug benutzt, der von
I905 auf 2,5V gehalten wird, versorgt von Hochzieh-Widerstand R968. Stift 4 benutzt R961/R962 und R955/R959 als
Spannungsteiler, der verbunden ist durch die +10V und T900 Wicklung durch D959, die im Vorwärts-Stromrichter-Betrieb ist.
Während des Betriebs heißt das, Stift 4 wird unter dem Bezugspegel von Stift 5 gehalten, bis die Netzversorgung unterbrochen
wird, oder das Gerät wird ausgeschaltet, und dann steigt Stift 4 über Stift 5, und der Ausgangsstift 2 wird tief gesetzt. Dieses Tief
wird vom Mikroprozessor wahrgenommen. Im Normalbetrieb wird Stift 2 hoch gehalten durch den Hochzieh-Widerstand R990 von
der 5V Stromversorgung.
Die Schutzleitung (Stift 14) wird im Normalbetrieb von R971 von der 5V Stromversorgung hoch gehalten, das Hoch wird auf die
Schutzleitung und auf den Mikroprozessor angewandt. Wenn die Schutzleitung tief gesetzt wird, geht das Gerät in den
Bereitschaftsbetrieb, das Gerät kann wieder eingeschaltet werden durch die normalen Methoden, mit denen man es aus der
Bereitschaft herausholt, aber wenn die Ursache für die Aktivierung des Schutzschaltkreises nicht behoben wird, wird das Gerät
wieder in den Bereitschaftszustand zurückkehren.
Der Überlaststrom für die 16V Audioversorgung benutzt Komparator 1, die Widerstände R967 und R964 bauen auf Stift 6 eine
Vergleichsspannung auf. Die verglichene Spannung wird zu Stift 7 gespeist mit Hilfe des Spannungsteilers R968 und R966, der von
der Ausgangsseite des Stromfühlungswiderstands R974 versorgt wird. Sollte die Spannung bei Stift 7 unter die von Stift 6 fallen,
wird Stift 1 tief gesetzt , wodurch die Schutzleitung über D958 tief gesetzt und das Gerät in Bereitschaft versetzt wird.
Komparator 3 wird benutzt, um vor einem Schichtkurzschluss innerhalb von F.B.T. zu schützen, er dient auch als Schutz vor
Kurzschlüssen bei den Sekundärausgängen von F.B.T. I903 wird mit ca. 16V über D960 an Stift 3 versorgt, von dieser Versorgung
wird eine Vergleichsspannung zu Stift 9 gespeist mit Hilfe von Spannungsteiler R972/R969, gespeist über die Z948 Versorgung.
Stift 8 wird von einem anderen Spannungsteiler versorgt, der diesmal aus drei Widerständen R973/R970 und R760 besteht und den
Strom prüft, der durch Q752 fließt, sollte dieser zunehmen, wird der Spannungsabfall über R760 größer werden und die Spannung
von Stift 8 erhöhen, wenn sie Stift 9 überschreitet, und Stift 14 wird tief gesetzt, wodurch das Gerät in Bereitschaft versetzt wird.
Komparator 4 wird benutzt zum Schutz vor Höchstspannung /Überspannung, da alle F.B.T. Sekundärspannungen proportional sind,
wird die 200V Versorgung zur Basis der Kathodenstrahlröhre (CRT) benutzt, um die für den Vergleich benötigte Spannung zu
erzeugen, dies wird erreicht mit einem Spannungsteiler, bestehend aus R718, R749 und R719. Z708 überwacht die Spannung bei
der Verbindung von R718 und R749, wenn sie 36V überschreitet, wird die Z-Diode leitend und legt ein Hoch an Stift 10 von I903 an,
dies wird mit der Vergleichsspannung an Stift 11 verglichen, der auch die von I905 eingestellten 2,5V benutzt. Wenn Stift 10 höher
ist als 2,5V, wird Stift 13 tief gesetzt, was seinerseits die Schutzleitung über D957 tief setzt und dadurch das Gerät in Bereitschaft
versetzt.
Die Niederspannungsleitungen werden geschützt durch die Dioden D931, D932 und D930, sie sind in Sperr-Vorspannung
verbunden von der Schutzfühlungsleitung bis zur 8V und 5V Versorgung. Die +5V Bereitschaftsverbindung wird durch D986
geschützt, die den Bezug Z950 tief setzt, wenn am Ausgang von I952 ein Kurzschluss zu sehen ist. Der +16V Phonoausgang hat
eine Diode zurück zu Stift 5 I903 im Falle eines Kurzschlusses.
Wenn die +B oder Audio-Stromversorgung vor dem Schutz auf der Sekundärseite der Stromversorgung an Masse kurzschließt, wird
der primäre Stromüberlastschutz (Stift 3 I900) wirksam und schaltet die Ansteuerungsausgabe von Stift 6 I900 ab. Eine
Sperrschaltung Q955/R998/RP01/C964 wird wirksam, um die Stromversorgung auf Bereitschaft zu schalten (unter
Störungsbedingung), falls die Software nicht bei Stift 14 I903 tief wirksam wird. Verzögerung vor Sperre eingestellt durch
C964/R994. +B erhält über Z907 Schutz vor Überspannung, Z907 schließt kurz, wenn die +B Spannung 180V Gleichstrom
übersteigt.
DTI-NETZTEIL
SCHALTKREIS-BESCHREIBUNG
Die Stromversorgung wird über { TV ein } eingeschaltet. An diesem Punkt wird der Netz-Wechselstrom durch D8, D10, 11, 12
gleichgerichtet, was ca. 340v Gleichstrom über C58 herstellt. Dies wird dann über die Primärwicklung von T1 auf den Drain von Q4
Summary of Contents for C28W40TN
