160
Der integrierte Schaltkreis enthält einen automatischen farbbegrenzenden Schaltkreis, der schaltbar ist, was Übersättigung
verhindert, wenn Signale mit einem hohen Chrominanz-zu-Farbsynchronsignal-Verhältnis empfangen werden. Der acl Schaltkreis
ist so konzipiert, dass er nur das Chrominanzsignal vermindert und nicht das Farbsynchronsignal. Dies bietet den Vorteil, dass die
Farbempfindlichkeit nicht von dieser Funktion betroffen wird.
Der SECAM Decoder enthält einen selbstkalibrierenden PLL Demodulator, der zwei Bezüge hat, die 4,43MHz
Zwischenträgerfrequenz, die vom Quarzschwinger erhalten wird, welcher benutzt wird, um die PLL auf die gewünschte frei laufende
Frequenz abzustimmen, und den Bandabstands-Bezug, um den korrekten absoluten Wert des Ausgangssignals zu erhalten. Der
spannungsgesteuerte Oszillator (VCO) der PLL wird bei jeder vertikalen Schwarztastungsperiode kalibriert, wenn der integrierte
Schaltkreis in der Such- oder SECAM-Betriebsart ist. Die Grundbandbreiten-Laufzeitkette ist in das Paket integriert.
BILDVERBESSERUNG - PHILIPS TDA 9178.
Der integrierte Schaltkreis (IC) für Bildverbesserung ist ein Analog-Video-Prozessor mit drei hauptsächlichen
Verarbeitungsfunktionen; Luminanzvektor, Farbvektor und Spektralverarbeitung. Gegenwärtig werden die folgenden Einrichtungen
umgesetzt; Luminanz-Spannungsspitzen-Verbesserung (LTI), Farb-Spannungsspitzen-Verbesserung (CTI), variable Gamma-
Regelung und bildabhängige nichtlineare Y und U, V Verarbeitung durch Luminanz-Histogramm-Analyse.
Der Spektralprozessor bietet Luminanz-Spannungsspitzen-Verbesserung, Luminanz-Detail-Verbesserung durch intelligentes
Peaking und Farbstufenverbesserung. Die Steuerung für Zeilenbreite kann vom Benutzer definiert werden. Der Luminanzvektor-
Prozessor, die Transferfunktion werden nichtlinear gesteuert durch eine Histogramm-Analyse gemessener Luminanzwerte, die in
einem Bild gemessen werden. Infolgedessen wird das Kontrastverhältnis der wichtigsten Teile der Szene verbessert. Eine variable
Gammafunktion nach der Umwandlung bietet die Möglichkeit für alternative Helligkeitsregelung oder Werkseinstellung der Bildröhre.
Bei digitalen Modellen liefert der integrierte Schaltkreis für Bildverbesserung die Funktionen Schärfe, Rauschminderung und Farb-
Spannungsspitzen-Verbesserung, während die 100Hz/Zeilenfolgeverfahren-Modelle diese Funktionen im Doppelabtastungsmodul
liefern. Alle beschriebenen Funktionen können über die Auswahlmöglichkeiten im Wartungsmenü durch die I
2
C Steuerung
geschaltet/geregelt werden.
Y, U und V Signale werden von den I200 Stiften 49, 50 & 51 genommen und gehen direkt in Y
in
U
in
und V
in
(Stifte 6, 8 und 9 von
IE01). Die verstärkten Y, U & V Ausgaben kommen von IE01 (Stift 19 bzw. 17 bzw. 16) und gehen zu IE02 (Stift 28 bzw. 27 bzw.
26).
TUNER.
Der Tuner U100 ist ein Frequenz-Synthese-Typ mit einer unsymmetrischen Eingabe und der Stromversorgung von der +5V
Schiene, während die Abstimmspannung von der +33V Schiene kommt, geliefert vom Schaltkreis für waagerechte Ablenkung.
Direkter Frequenzzugang, Kanalwahl, automatische Lautstärkeregelung (AGC) und automatische Scharfabstimmung (AFC) werden
über den I
2
C Bus gesteuert. Die Steuerung für AGC, AFC und Versetzung kann gewählt werden, indem man in das Wartungsmenü
geht und ‘Tuner’ auswählt.
Stift 1, AGC wird von Stift 62 von TDA 9320 genommen. Die symmetrische Zwischenfrequenz-Ausgabe wird von den Stiften 10 &
11 genommen, die zur Eingabe der Bild- und Ton- SAW Filter (Stifte 1 & 2) gelangen. Die Ausgaben von X200 und X202 (Stift 4
bzw. 5) passieren durch Stifte 2 & 3 und Stifte 63 & 64 von I200, wo sie demoduliert werden.
RGB PROZESSOR - TDA 9330.
VERTIKALE ABLENKUNG & GEOMETRIE-STEUERUNG.
Der Ansteuerungsschaltkreis für die vertikalen und Ost-West-Ablenkungs-Schaltkreise wird durch einen Vertikal-Frequenz-Teiler
erzeugt, der seinen Taktgeber vom Zeilenoszillator bekommt. Der Frequenz-Teiler wird durch den ankommenden Vertikalimpuls
synchronisiert, der vom Eingabeprozessor oder vom Zusatzkasten erzeugt wird.
Die vertikale Ansteuerung wird durch einen differentiellen Ausgangsstrom verwirklicht. Die Ausgaben müssen direkt an die vertikale
Ausgangsstufe angekoppelt werden. Die vertikale Geometrie kann durch I2C Steuerung über das Wartungsmenü justiert werden.
HORIZONTALE SYNCHRONISIERUNG & ANSTEUERUNGS-SCHALTKREIS.
Das Signal für horizontale Ansteuerung wird von einem internen, spannungsgesteuerten Oszillator erhalten, der mit einer Frequenz
von 13,75 MHz läuft. Dieser Oszillator wird durch einen Resonanz-Oszillator 12 MHz auf diese Frequenz stabilisiert. Der interne,
spannungsgesteuerte Oszillator wird durch einen PLL-Kreis mit interner Zeitkonstante auf den ankommenden horizontalen Hd
Impuls synchronisiert. Das Signal für horizontale Ansteuerung wird durch einen zweiten Regelkreis erzeugt, der die Phase des
Bezugssignals vom internen, spannungsgesteuerten Oszillator mit dem Rücklaufimpuls vergleicht. Der Zeitkonstantenkreis ist
intern. Der integrierte Schaltkreis hat eine dynamische horizontale Phasenkorrektureingabe, die dazu benutzt werden kann,
Phasenverschiebungen zu kompensieren, die durch Strahlstromschwankungen verursacht werden. Zusätzliche Einstellungen der
horizontalen Ablenkung, die über den zweiten Kreis erreicht werden, sind die Horizontalregelung und die Parallelogrammkorrektur.
Das Signal für horizontale Ansteuerung wird mit Hilfe des Verfahrens für weichen Start/weichen Stop ein- und ausgeschaltet. Diese
Funktion wird verwirklicht durch eine Veränderung von Ton vom Impuls für horizontale Ansteuerung. Bei
Höchstspannungsimpulsgeneratoren ohne Spannungsteiler, kann der integrierte Schaltkreis in einer Betriebsart für festen
Strahlstrom eingestellt werden. Dann wird die Bildröhrenkapazitanz mit einem Strom von ca. 1mA entladen, was durch den
Schwarzpegel-Rückkopplungskreis bestimmt wird. Wenn die Möglichkeit für festen Strahlstrom ausgewählt ist, ist es immer noch
möglich, beim Ausschalten einen schwarzen Bildschirm zu haben. Das kann erreicht werden, indem man die vertikale Ablenkung in
eine Überabtastungsposition bringt.
Eine zusätzliche Funktion des integrierten Schaltkreises ist das Einschalten mit Niederleistung. Diese Betriebsart wird aktiviert,
wenn eine Speisespannung von 5V an den Einschalt-Stift gelegt wird. Der für diese Funktion erforderliche Strom ist typischerweise
3mA. Unter dieser Bedingung hat das Signal für horizontale Ansteuerung das normale Toff und Ton steigt allmählich von Null auf
ca. 30% des Normalwerts. Das führt zu einer Zeilenfrequenz von ca. 50kHz oder 25kHz. Das Ausgangssignal bleibt unverändert,
bis die Netzspannung eingeschaltet wird. Dann geht das Signal für horizontale Ansteuerung allmählich mit Hilfe des Verfahrens für
weichen Start zur normalen Frequenz und zum Arbeitszyklus über.
Summary of Contents for C28W40TN
