92
CONNEXIONS D'ALIMENTATION
•
La broche 10
(VDDM) est l'alimen5V pour l'interface de mémoire externe. Sans cette alimentation, le
microcontrôleur ne peut pas communiquer avec l'EPROM/MTP (ou SRAM).
•
La broche 34
(VDD) est la tension d'alimentation numérique principale du CI (5V avec une tolérance de 10%).
•
La broche 52
(VDDA) est la tension d'alimentation numérique pour le CNA et les PLL (+5V). Ces connexions sont toutes
regroupées sur le rail de 5V du téléviseur, pour assurer que le microcontrôleur fonctionne même dans le mode de
veille.
CONNEXIONS DE L'OSCILLATEUR À QUARTZ
•
La broche 11
est l'entrée de l'oscillateur à quartz 4MHz (OSCIN).
•
La broche 12
est la sortie de l'oscillateur à quartz 4MHz (OSCOUT). En connectant une sonde d'oscilloscope x100 à la
broche 11, la présence d'une onde sinusoïdale de 4MHz à la sortie d'oscilloscope du microcontrôleur peut être confirmée.
CONNEXION DE REMISE À ZÉRO
•
La broche 54
est l'entrée REMISE A ZÉRO active au niveau bas du microcontrôleur. Cette entrée est normalement au
niveau haut (+5V environ) dans les conditions d'exploitation, mais change d'état lorsque l'alimentation de 5V tombe
en dessous de 4,5V. Dans ce cas, le CI de remise à zéro (I021) met la broche 54 au niveau bas jusqu'à ce que son
entrée monte au-dessus de 4,5V. La diode (D001) assure la décharge rapide du condensateur (C015) en cas de panne
d'alimentation de veille, de manière à ce que la remise à zéro fonctionne rapidement. Le condensateur (C015) se charge
lentement lorsque l'alimentation de 5V est restaurée, pour assurer une certaine hystérésis.
ENTRÉE DU RÉCEPTEUR INFRAROUGE (IR)
•
La broche 25
est la sortie filtrée du récepteur IR. Cette entrée du récepteur IR est constituée d'impulsions à modulation
en largeur (PWM) comprises entre 0V et +5V, qui sont décodées par le microcontrôleur en commandes utiles provenant
de la télécommande. Lorsqu'une commande valide a été décodée, la LED rouge sur le devant du téléviseur clignotera
brièvement.
CONNEXIONS DE SYNCHRONISATION HORIZONTALE ET VERTICALE
•
La broche 48
est l'entrée de synchronisation verticale de l'étage de déflexion. Cette entrée est utilisée pour assurer que
l'OSD est affiché dans une position verticale stable. Lorsque le téléviseur en est mode veille, cette entrée est
normalement au niveau bas. L'entrée verticale est déclenchée pour le front ascendant (polarité positive).
•
La broche 9
est l'entrée de synchronisation horizontale de l'étage de déflexion. Cette entrée assurer que l'OSD est
affiché dans une position horizontale stable. Lorsque le téléviseur en est mode veille, cette entrée est normalement au
niveau bas. Cette entrée est déclenchée par le front montant (polarité positive).
CONNEXIONS D'ENTRÉES GÉNÉRALES
ENTRÉE DE CASQUE D'ÉCOUTE
•
La broche 19
est utilisée pour détecter si un casque d'écoute a été inséré dans sa prise. Cette entrée est normalement
HAUTE (+5V) à moins que le casque ait été inséré, auquel cas elle est proche de 0V. Lorsque le casque est inséré,
l'option de mode casque est alors disponible sur le Menu "Mode Son" et les haut-parleurs (et le haut-parleur de graves si
installé) du téléviseur sont bloqués.
ENTRÉE DE PROTECTION
•
La broche 26
est utilisée pour déterminer su une faute de protection s'est produite sur le châssis. Cette ligne est
connectée aux sorties du comparateur 1, 13 et 14 de I903 dans l'ensemble d'alimentation. Cette ligne est normalement
HAUTE (+5V environ) à moins qu'une faute se soit produite, auquel cas elle est proche du potentiel de la masse (0V).
•
La sortie 1 du comparateur surveille le rail d'alimentation audio +16V pour tout signe de surintensité. Si ce rail est court-
circuité, ou tire trop de courant, la sortie du comparateur (broche 1 de I903) changera d'état à 0V.
•
La sortie 13 du comparateur surveille la tension EHT produite par le FBT dans le circuit de déflexion. Si cette tension est
trop élevée, cette sortie sera au niveau bas pour indiquer qu'il y a un problème de déflexion.
•
La sortie 14 du comparateur est connectée au secondaire du transformateur d'entrée de la ligne de déflexion. Elle est
principalement utilisée pour indiquer un tirage excessif de courant du transformateur d'entrée de ligne et du FBT.
ENTRÉE ALIMENTATION CORRECTE
•
La broche 27
est utilisée pour indiquer toute coupure d'alimentation du téléviseur ou lorsqu'une décharge statique s'est
produite. Cette entrée est piloté par interruption pour réagir instantanément en cas de front descendant. Dans ces
circonstances, les amplificateur de puissance audio sont bloqués et le téléviseur commence à se mettre en mode veille.
Cette entrée est dérivée de la sortie du comparateur (broche 2 de I903) dans l'ensemble d'alimentation. Ce comparateur
fournit une "alerte rapide" comme quoi l'alimentation principale a été coupée ou d'une décharge statique s'est produite. En
cas de décharge statique, le téléviseur passera temporairement au mode veille avant de se remettre sous tension
quelques secondes plus tard.
ENTRÉE PANNE DE VENTILATEUR DTT
•
La broche 32
est utilisée seulement sur châssis D8 équipé d'un module DTT. Elle est utilisée pour indiquer toute panne
du ventilateur du module DTT (par exemple, si le ventilateur est bloqué). Cette entrée est normalement HAUTE (+5V
environ) à moins qu'une panne ait été détectée (0V). Elle est utilisée pour indiquer toute panne du ventilateur du module
DTT (par exemple, si le ventilateur est bloqué). Cette entrée est normalement HAUTE (+5V environ) à moins qu'une
panne ait été détectée (0V).
Summary of Contents for C28W40TN
