![background image](http://html.mh-extra.com/html/hilti/ps200-ferroscan/ps200-ferroscan_operating-instruction_2136437055.webp)
53
en
The completed Imagescan is shown shaded. Attach a
new grid to the wall so that the edges of the reference
grid overlap and the scan areas are aligned as shown in
the diagram.
Select the location of the next Imagescan and repeat
the scanning process. Completed Imagescans may be
repeated by simply reselecting the area to scan and per-
forming the Imagescan process. The data will be over-
written. When sufficient Imagescans have been made,
or when all nine are complete, press
Cancel
to return
to the main menu and transfer the data to the monitor.
Please refer to section 7.4.
-CAUTION-
Pressing the
Cancel button
twice causes the recorded
Imagescan to be deleted. The screen then returns to the
main menu.
7.2.8 Error messages from the scanner when
starting or scanning
Error messages may be displayed graphically on the
scanner. Generally, a stop symbol indicates a fatal error
with the scanner. In this case, the scanner requires to
be serviced at a Hilti repair center.
or
One of these symbols may be displayed immediately
after the scanner is switched on. They indicate a possi-
ble electronic fault. Switch the scanner off and then back
on again. If the error message appears again, the appli-
ance will need to be sent to Hilti for repair.
An exclamation symbol indicates either an error caused
by the operator or an error that can be solved by the
operator.
150
150
300
450
600
300
450
600
5
6
7
8
1
2
3
4
150
150
300
450
600
300
450
600
5
6
7
8
1
2
3
4
This symbol may appear either when trying to enter the
Imagescan or Blockscan scanning mode, when trying
to begin a new Imagescan within Blockscan scanning
mode or when trying to start Quickscan recording. It
indicates that the memory allocated for the operation is
full and that no more data can be stored. In this situa-
tion, the data must either be transferred to the monitor
or deleted from scanner memory.
-WARNING-
Deleting the scanner memory may result in permanent
data loss. Data that has not been transferred to the mon-
itor will be permanently deleted.
This symbol may appear during any type of scanning
when the Scanner is being moved over the surface. It
indicates that the Scanner is being moved too quickly
to allow it to process all the signals generated. The max-
imum speed is 0.5m/s or 20 inches/s.
If the symbol appears during Quickscan detection, press
Confirm
and repeat the scan. During Quickscan record-
ing, press
Confirm
. You will need to begin the record-
ing operation again from the original starting point or
from where the last marker was set. During Imagescan,
press
Confirm
and repeat the row or column previous-
ly scanned. In all cases, move the scanner more slow-
ly over the surface.
This symbol may appear if the scanner has been moved
in the wrong direction during scanning, e.g. you begin
scanning from right to left but during the scan move the
scanner toward the right. The warning does not appear
immediately, but only when moved 15 cm or more in
the wrong direction.
7.3 Operating the monitor
The monitor provides extensive data storage capability,
the ability to analyze scan data at the site where it was
collected and also to add voice records to scans.
Printed: 07.07.2013 | Doc-Nr: PUB / 5070389 / 000 / 00
Summary of Contents for PS200 Ferroscan
