HikRobot MV-CL042-91CC User Manual Download Page 96

Page: 96 / 120

Camera Link Line Scan Camera

User Manual

Chapter 12 Trouble Shooting

Table 12-1

Trouble Shooting

No. Trouble

Possible Reason

Solution

No camera found when
running the client.

Camera  is  not  started  up
normally,  or  Camera  Link
cable connection exception.



Check camera power wiring (observe
the LED indicator).



Check whether Camera Link cable is
normally connected via serial port
tool.



Reinstall the client.

Camera indicator shows
solid blue, but frame
grabber

software

cannot generate image.



Incorrect

parameter

settings

frame

grabber software.



Camera is in trigger
mode.



Check whether parameter settings of
frame grabber software are set
correctly.



Disable trigger mode.

Live view is black.

Aperture is closed.

Open the aperture.

Live view is normal, but
camera

cannot

triggered.

Incorrect I/O wiring or
trigger mode is not enabled.



Check whether the I/O wiring is
correct

under

corresponding

triggering mode.



Check whether the camera trigger
mode and related trigger signal input
are normal.

Live  view  and  trigger
signal  are  normal,  but
camera  cannot  get  the
image  required  by  the
algorithm.

The image output format
does not match.

Confirm the image format required by the
algorithm and adjust the image output
format of the camera in client software.

Summary of Contents for MV-CL042-91CC

























































































































Search results

Summary of Contents for MV-CL042-91CC

Reviews:

Related manuals for MV-CL042-91CC

Brands by name

Popular brands

HikRobot MV-CL042-91CC, User Manual

Search results

Summary of Contents for MV-CL042-91CC

Reviews:

Related manuals for MV-CL042-91CC

Brands by name

Popular brands