HikRobot MV-CL042-91CC User Manual Download Page 100

Page: 100 / 120

Camera Link Line Scan Camera

User Manual

Parameter

Command

Value

Description

r OffsetY

Read vertical offset from
the origin to the region of
interest (in pixels).

Reverse X

w ReverseX x

0—disable

1—enable

Set image reverse X.

E.g., w ReverseX 1.

r ReverseX

Read image reverse X.

Direction Source

w DirectionSource x

0—Internal (internal
control)

1—CC 3 (external
control)

Set control source of scan
direction. E.g., w
DirectionSource 1.

r DirectionSource

Reverse Scan
Direction

w ReverseScanDirection
x

0—forward direction

1—reverse direction

Set scan direction (internal
control). E.g., w
ReverseScanDirection 1.

r ReverseScanDirection

Read scan direction.

PixelFormat

w PixelFormat x

0x1080001--momo8

0x1100003--mono10

0x1100005--mono12

0x02180014--RGB 8

Set pixel format. E.g., w
PixelFormat 0x1080001.

r PixelFormat

Read pixel format.

Note: the returned value
is decimal system and it
needs to be converted to
hexadecimal.

PixelSize

r PixelSize

Read pixel size.

Test Pattern

w TestPattern x

：

0—off

14—ObliqueMonoBar

Set test pattern. E.g., w
TestPattern 14.

Summary of Contents for MV-CL042-91CC

























































































































Search results

Summary of Contents for MV-CL042-91CC

Reviews:

Related manuals for MV-CL042-91CC

Brands by name

Popular brands

HikRobot MV-CL042-91CC, User Manual

Search results

Summary of Contents for MV-CL042-91CC

Reviews:

Related manuals for MV-CL042-91CC

Brands by name

Popular brands