![background image](http://html2.mh-extra.com/html/hand-held-products/scanteam-2070/scanteam-2070_system-manual_3568137085.webp)
3 - 23
Auxiliary Port Input Communications
Aux Data Format Editor Selections
The Aux Data Format Editor selections are used to edit incoming data to the aux
port. For example, you can use the Aux Data Format Editor to insert characters
at certain points in bar code data as it is scanned.
It is not necessary to use the Aux Data Format Editor. A set of defaults for the
aux data format is already programmed in the base. The selections in the
following pages are used only if you wish to alter the default settings.
Default Aux
Data Format setting = none.
If you have changed aux data format settings, and wish to clear all formats and
return to the defaults, scan the
Default Aux Data Format
code.
To Add an Aux Data Format
Step 1.
Scan the
Enter Aux Data Format
symbol (page 3-27).
Step 2. Primary/Alternate Format
Determine if this will be your primary aux data format, or one of 3
alternate formats. (Alternate formats allow you “single shot” capability
to scan one bar code using a different aux data format. After the one
bar code has been read, the scanner reverts to the primary aux data
format. See page 3-28.) If you are programming the primary format,
scan
0
. If you are programming an alternate format, scan
1
,
2
, or
3
,
depending on the alternate format you are programming.
Step 3. Terminal Type
Refer to the Supported Terminals Chart (page 2-6) and locate the
Terminal ID number for your PC. Scan 3 numeric bar codes on the
inside back cover to program the scanner for your terminal ID (you
must enter
3
digits). For example, scan
0 0 3
for an IBM AT.
Note: To apply a format to all terminal types, a universal code of
099
is used.
Step 4. Code I.D.
Scan 7 then 2 from the Programming Chart. (This is the hex value for
“r,” the aux port I.D.)
Step 5. Length
Specify what length (up to 9999 characters) of data will be acceptable
for this symbology. Scan the 4 digit data length from the Programming
Chart. (Note: 50 characters is entered as 0050. 9999 is a universal
number, indicating all lengths.)
Summary of Contents for SCANTEAM 2070
