GW Instek LCR-6000 Series User Manual Download Page 60

Page: 60 / 143

Setup Key

To set up the Auto LCZ Function

Step 1.  Press the [Setup] key
Step 2.  Use the cursor key to select [AUTO LCZ] field
Step 3.  Use the soft-keys to turn on/off the Auto

LCZ Function.

Soft-key

Function

OFF

Turn off the Auto LCZ Function

Turn on the Auto LCZ Function.

When Auto LCZ Function is set to ON,
“AUTO-LCZ” will display on [FUNC]

field.

NOTE

The Auto LCZ Function will be turned off after you
set the measurement function.

5.1.5 Monitor 1 and Monitor 2 [MON 1][MON 2]

The LCR-6000 Series can monitor the other two

parameters.

NOTE

Additional monitoring parameters do not
increase the instrument measurement time.
Monitor parameter display in [MEAS DISPLAY]
page and [ENLARGE] page.

Procedure for setting monitor parameters (monitor 1
and monitor 2)

Step 1. Press the [Setup] key.
Step 2. Use the cursor key to select [MON 1] or

[MON 2] field.

Step 3. Use the soft-keys to select DC bias voltage.
Soft-key

Function

OFF

Turn off the monitor

Absolute value of impedance

Dissipation factor

Quality factor(=1/D)

Vac

Test signal Voltage

Iac

Test signal Current

Absolute deviation value

Δ%

Relative deviation value

θr

Phase radian

Summary of Contents for LCR-6000 Series
















































































































































Search results

Summary of Contents for LCR-6000 Series

Reviews:

Related manuals for LCR-6000 Series

Brands by name

Popular brands

GW Instek LCR-6000 Series, User Manual

Search results

Summary of Contents for LCR-6000 Series

Reviews:

Related manuals for LCR-6000 Series

Brands by name

Popular brands