GTE COBOSAFE CBSF Operating Manual Download Page 46

Page: 46 / 48

COSTUMER SERVICE

CoboSafe-CBSF

325-2810-012US15

17 Costumer Service

Scope of customer service

■

Mediation of authorized contact persons for the calibra-

tion

■

Spare part orders

■

Assistance with problems with the measuring system

Phone

Customer service is available from

Mo - Thu from 8:00 to 16:00 (08 AM – 04 PM)

Fridays from 8:00 to 14:30 (08 AM – 02:30 PM)

+49 2162 3703-0

E-mail

[email protected]

Postal address

GTE Industrieelektronik GmbH

Customer Service

Helmholztstraße 21

41747 Viersen, Germany

Further information

www.cobosafe.com

18 Disposal

Improper disposal

Environmental damage due to improper disposal!

■

Do not dispose of the measuring system in residual waste.

■

Dispose of all components according to regulations at the

place of use.

The measuring system contains components that can damage the

environment if disposed of improperly.

18.1 Disposal by the Manufacturer

The measuring device can be returned for disposal by the manufacturer at the end of its service

life. Contact customer service before sending the device.

Fig. 24: Disposal

Summary of Contents for COBOSAFE CBSF

















































Search results

Summary of Contents for COBOSAFE CBSF

Reviews:

Related manuals for COBOSAFE CBSF

Brands by name

Popular brands

GTE COBOSAFE CBSF, Operating Manual

Search results

Summary of Contents for COBOSAFE CBSF

Reviews:

Related manuals for COBOSAFE CBSF

Brands by name

Popular brands