manualshive.com logo in svg

Gossen MetraWatt SECULIFE ST PRO, Manual, Page: 97 / 114

Share
Download
Gossen MetraWatt SECULIFE ST PRO Manual Download Page 97

GMC-I Messtechnik GmbH

97

Error while writing the data backup file to 
the USB flash drive

There’s not (no longer) enough avail-
able memory space on the storage 
medium.

–

In particular in the case of FAT16 
formatted USB flash drives: too 
many files on the USB flash drive

–

Power consumption of the utilized 
USB flash drive exceeds 500 mA.

–

The USB flash drive was discon-
nected during data import.

–

The USB flash drive is defective or 
incompatible with the test instru-
ment.

➭

Make sure that a at least 100 MB is 
available on the USB flash drive 
and delete any data files which are 
no longer required.

➭

If the problem persists, save the 
data from the USB flash drive to 
another storage device and refor-
mat the USB flash drive (FAT32).

➭

Only use USB flash drives with 
power consumption of less than 
500 mA in combination with the 
test instrument.

➭

Make sure that the USB flash drive 
isn’t disconnected or moved until 
the entire data backup process has 
been completed.

➭

If none of these measures results in 
improvement, replace the USB 
flash drive. A list of tested USB 
flash drives is included in section 
14.3.

Moving of an object has failed

Moving a test object would lead to an 
ID conflict. The ID already exists for this 
customer.

➭

Delete the object with duplicate ID.

➭

Select another customer as a relo-
cation target.

Errors During Operation with Barcode or RFID Scanner

–

The scanned barcode is too long.

–

While writing an RFID tag an 
attempt was made to write an ID to 
the tag with vowel mutations such 
as ä, ü or ö, or with special charac-
ters.

➭

Change vowel mutations such as ä 
to ae.

➭

Avoid the use of special characters 
in the ID.

Error Messages

Possible Causes

Corrective Measures

Summary of Contents for SECULIFE ST PRO



















































































































Reviews:

No comments