manualshive.com logo in svg

Gossen MetraWatt SECULIFE ST PRO, Manual, Page: 57 / 114

Share
Download
Gossen MetraWatt SECULIFE ST PRO Manual Download Page 57

GMC-I Messtechnik GmbH

57

Test Sequence

➭

Before conducting any leakage current measurements, make 
sure that the “Ref. voltage L-PE” and “Alt. Test Freq.” mea-
surement parameters have been correctly set in SETUP (see 
section 6.2).

➭

Set the rotary switch to the 

I

A

 position.

➭

Connect the DUT in accordance with the selected measuring 
method.

➭

In the case of measurement type APP: Connect the applied 
parts.

➭

Select the measurement type: 
– By setting the parameters 
or 
– Directly via the 

Measurement Type

 key

 

➭

In the case of measurement type APP: 
Additionally select the respective applied parts by set-
ting the utilized sockets to “on” and the unused sockets 
to “off”. 

➭

In the case of 

direct measurement

, measurement must 

be performed with mains plug polarity in both direc-
tions. Select the respective polarity to this end by 
pressing the 

NL/LN

 key. 

➭

Start the test:

 press the 

START

/STOP

 key. 

➭

After each reconnection to the mains, and as soon as 
the first test is started, a mains connection test is exe-
cuted.

➭

In the case of measurement type direct P1 or direct APP:

 

Acknowledge the warning which indicates that line 
voltage will be connected to the test socket. 

➭

Switch the device under test on.

➭

Contact the short-circuited applied parts with the test probe.

➭

The measured values are displayed. The measured 
value recording symbol shown at the right appears. 
Each time this key is pressed, the currently displayed 
measured value is saved to buffer memory.

➭

Turn off the device under test.

➭

End the test:

 press the 

START

/STOP

 key. 

The save symbol appears (floppy disk showing the 
number of measured values stored to buffer memory) 
and prompts you to save the measured values to an ID 
number.

➭

Read the measured values and compare them with the 
table of permissible limit values.

➭

Press the 

ESC

 key in order to discard the measured 

values stored to buffer memory and acknowledge by 
pressing the key shown at the right. 

See limit values in section 14.8.

Summary of Contents for SECULIFE ST PRO



















































































































Reviews:

No comments