manualshive.com logo in svg

Gossen MetraWatt SECULIFE ST PRO, Manual, Page: 85 / 114

Share
Download
Gossen MetraWatt SECULIFE ST PRO Manual Download Page 85

GMC-I Messtechnik GmbH

85

❑

Suppressing Test Steps

Depending on the selected test standard, some of the following 
test steps can be suppressed: 

1

Before switching line voltage to the device under test, a short-circuit test 
is conducted regardless of this setting.

❑

Setting Measuring Parameters for Individual Test Steps 

Depending on the selected test standard, some of the following 
test steps can be selected: 

1

Feature G01

2

Feature G02

❑

Selecting Between Single and Multiple Measurement for Individual Test 
Steps 

❑

Setting Measurement Duration for Individual Test Steps

Testing time for the respective measurement can be influenced 
with these parameters. If a test step for a single measurement is 
involved, the entire test step has a duration of the time entered in 
seconds. If a test step for a multiple measurement is involved, the 
measurement duration for each measuring point is influenced.
If 0 seconds is selected, continuous measurement is conducted 
which can only be ended by pressing a key.
 

1

In the case of test sequence VDE 0701-0702-PRCD with a setting of 
“PRCD type: PRCD (SPE)”, measurement duration 

cannot

 be influenced. 

The measurement duration which has been set here only affects the 
RPE measurement with PRCD types “PRCD (standard)” and “PRCD-S 
(SPE)”.

Parameter

Suppressible test steps

Visual inspection (1)

Visual inspection, standard

Visual inspection 2

Visual inspection, function test, welding units

Function test

Function test

RPE

Protective conductor resistance test

RINS PCI+II 

Insulation resistance tests for PCI and PCII

RINS pri./sec.

Insulation resistance test between the primary and sec-
ondary sides of PCIII DUTs

RINS sec./PE

Insulation resistance test between the secondary side and 
PE of PCIII DUTs

Polarity reversal

All leakage current measurements with reversed polarity 

IPE measurement type 
(active)

Protective conductor current test

IT

Touch current test

IT welding circuit

Touch current test at welding circuit

Display test instructions

Test instructions which are not necessarily required for experi-
enced inspectors.

Short-circuit test L-N

Short-circuit test between L and N 

1

Short-circuit test LN-PE

Short-circuit test between LN and PE1 

1

Open-circuit voltage
(IEC 60974-4)

Open-circuit voltage at welding unit

Continuity test 
(VLTG test only)

Continuity test with EL1/VL2E/AT3-IIIE adapter

PCIII supply voltage

Supply voltage measurement (with PCIII DUTs, for mea-
surement type “Active” only)

Parameter

Meaning

RPE IP

Select test current for protective conductor resistance 
test: 200 mA AC, 

±

200 mA DC, 10 A AC

1

 or 25 A AC

2

IPE measurement type 
(active)

Set measurement type of the protective conductor current 
measurement for the active device test (differential/direct)

IE measurement type 
(active)
(IEC 62353)

Set measurement type of the device leakage current mea-
surement for the active device test (differential/direct)

Parameter

Meaning

RPE as

Switch the “protective conductor resistance” test step back 
and forth between multiple and single measurement

Parameter

Meaning

RINS PC II as

Switch back and forth between multiple and single mea-
surement for the insulation resistance measurement at 
PC II parts (measurements at applied parts and welding 
outputs are not affected)

IT as

Switch back and forth between multiple and individual 
measurement for the touch current measurement

IT PC II as

(IEC 60974 only) Switch back and forth between multiple 
and individual measurement for touch current measure-
ment at PC II parts

Parameter

Meaning

RPE measurement 
duration 

1

Set testing time for the protective conductor resistance 
measurement (0 to 60 seconds)

IPE measurement duration

Set testing time for the protective conductor current mea-
surement (0 to 60 seconds)

IE measurement duration

Set testing time for the device leakage current measure-
ment (0 to 60 seconds)

Parameter

Meaning

IT measurement duration 

Set testing time for touch current measurement 
(0 to 60 seconds)

IT PC II measurement 
duration 

(for IEC 60974 only) Set testing time for touch current 
measurement at PC II parts (with the exception of welding 
outputs) (0 to 60 seconds)

RINS PC II measurement 
duration 

Set testing time for RINS measurements at PC II parts (0 
to 60 seconds)

Summary of Contents for SECULIFE ST PRO



















































































































Reviews:

No comments