manualshive.com logo in svg

Gossen MetraWatt SECULIFE ST PRO, Manual, Page: 105 / 114

Share
Download
Gossen MetraWatt SECULIFE ST PRO Manual Download Page 105

GMC-I Messtechnik GmbH

105

13

Maintenance

13.1

Housing Maintenance

No special maintenance is required for the housing. Keep outside 
surfaces clean. Use a slightly dampened cloth for cleaning. Avoid 
the use of cleansers, abrasives and solvents.

13.2

Testing the Color Display and the Buzzer (self-test param-
eter)

The color display can be tested for failure of individual segments 
and loss of color components on page 3/3 of the setup menu in 
the SETUP switch position under the self-test parameter.
Beyond this, the buzzer can be tested for 3 different frequencies.

13.3

Software Update (system info parameter)

The current firmware or software version can be queried via the 
system info parameter (Setup 3/3).
The test instrument’s firmware can be updated via the USB port 
with the help of a PC. Updating is only possible via the proprietary 

Firmware Update Tool

 application.

➭

Before updating your test instrument’s firmware, make sure 
that your PC software is compatible with the current firmware 
version.

Attention!

!

Before updating the firmware, be sure to save the struc-
tures you have created and your measuring data, be-
cause they might be deleted during the update process 
(seesection 5.2.3, “Backing Up and Restoring Test 
Structures and Measurement Data”).

Note

Adjustment data are not overwritten during updating, and 
thus recalibration is unnecessary.

As a registered user (if you’ve registered your test instrument), 
you’re entitled to download the 

Firmware Update Tool

 and the cur-

rent firmware version free of charge from the 

myGMC

 page at 

www.gossenmetrawatt.com

.

You’ll also find operating instructions for the 

Firmware Update Tool

 

here.

Attention!

!

The interface cable may not be disconnected while up-
dating the firmware via the USB port. 

Attention!

!

The test instrument may not be disconnected from sup-
ply power while updating the firmware via the USB port.

13.4

Backup Battery for Real-Time Clock

The backup battery (lithium cell) should be replaced no later than 
after 8 years. Replacement can only be executed by the service 
department.
If backup battery voltage is too low, the date and time assigned to 
the test data no longer correspond to the actual time of recording. 
This may also influence sorting in the report generating software.
The instrument’s database itself isn’t affected by a depleted 
backup battery.

13.5

Fuse Replacement

The fuses may only be replaced when the instrument is voltage-
free, i.e. the instrument must be disconnected from mains supply 
power and may not be connected to a measuring circuit.
The fuse type must comply with the specifications in the technical 
data or the labeling on the instrument.

13.6

Recalibration

The measuring tasks performed with your instrument, and the 
stressing it’s subjected to, influence aging of its components and 
may result in deviation from the specified levels of accuracy.
In the case of strict measuring accuracy requirements, as well as 
in the event of use at construction sites with frequent stress due 
to transport and considerable temperature fluctuation, we recom-
mend a relatively short calibration interval of once per year. If your 
instrument is used primarily in the laboratory and indoors without 
considerable climatic or mechanical stressing, a calibration inter-
val of once every 2 to 3 years is sufficient as a rule.
During recalibration * at an accredited calibration laboratory 
(DIN EN ISO/IEC 17025), deviations from traceable standards 
demonstrated by your measuring instrument are documented. 
Ascertained deviations are used to correct display values during 
later use of the instrument.
We would be happy to perform DAkkS or factory calibration for 
you at our calibration laboratory. Further information is available 
on our website:
www.gossenmetrawatt.com (

→

 Company 

→

 Quality and Certifi-

cates 

→

 DAkkS-Calibration Center 

→ 

Calibration Questions and 

Answers).
According to DIN VDE 0701-0702, only test instruments which 
are tested and calibrated at regular intervals may be used for test-
ing.
Recalibration of your instrument at regular intervals is essential for 
the fulfillment of requirements according to quality management 
systems per DIN EN ISO 9001.

* Examination of the specification, as well as adjustment, are not included 

in calibration. However, in the case of our own products, any required 
adjustment is performed and adherence to the specification is con-
firmed.

Summary of Contents for SECULIFE ST PRO



















































































































Reviews:

No comments