manualshive.com logo in svg

Gossen MetraWatt SECULIFE ST PRO, Manual, Page: 63 / 114

Share
Download
Gossen MetraWatt SECULIFE ST PRO Manual Download Page 63

GMC-I Messtechnik GmbH

63

Setting Measuring Parameters for IPA 

Note

The currently selected 

single fault

 is displayed on 

the initial page. In order to change it, it has to be 
selected and

 

set via the measuring parameters 

menu. 

Test Sequence

➭

Set the rotary switch to the 

I

PA

 position.

➭

Connect the DUT in accordance with the selected measuring 
type.

➭

Connect the applied parts.

➭

Select the measurement type: 
– By setting the parameters 
or 
– Directly via the 

Measurement Type

 key

 

➭

Select the respective applied parts by setting the utilized 
sockets to “on” and the unused sockets to “off”. 

➭

In the case of 

direct measurement

 

P1

, measurement 

must be performed with mains plug polarity in both di-
rections. Select the respective polarity to this end by 
pressing the 

NL/LN

 key. 

➭

Start the test:

 press the 

START

/STOP

 key. 

➭

After each reconnection to the mains, and as soon as 
the first test is started, a mains connection test is exe-
cuted.

➭

In the case of measurement type direct APP: 

Acknowledge the warning which indicates that line 
voltage will be connected to the test socket. 

➭

Switch the device under test on.

➭

The measured values are displayed. The measured 
value recording symbol shown at the right appears. 
Each time this key is pressed, the currently displayed 
measured value is saved to buffer memory.

➭

Turn off the device under test.

➭

End the test:

 press the 

START

/STOP

 key. 

The save symbol appears (floppy disk showing the 
number of measured values stored to buffer memory) 
and prompts you to save the measured values to an ID 
number.

➭

Read the measured values and compare them with the table 
of permissible limit values.

➭

Press the 

ESC

 key in order to discard the measured 

values stored to buffer memory and acknowledge by 
pressing the key shown at the right. 

See limit values in section 14.8.

Measuring 
Parameter

Meaning

Measurement Type 

Suitable for 
DUT Connection via

Direct APP

Direct measurement (via test 
socket) from the selected APP 
socket to all others.

Test socket

Perm. conn. APP

Measurement at the permanently 
installed DUT from the selected 
APP socket to all others.

Permanent connection

APP – applied parts 

 A / B / C / D / E / F / G / H / I / K, each individually (via on/off) to all other APPs

Single fault (SFC) – only with direct measurement type

Normal state / N interrupted / PE interrupted

Polarity 

Only with direct measurement 
type

L/N or N/L

Selection of polarity for mains voltage to the test socket

Summary of Contents for SECULIFE ST PRO



















































































































Reviews:

No comments