manualshive.com logo in svg

Gossen MetraWatt SECULIFE ST PRO, Manual, Page: 90 / 114

Share
Download
Gossen MetraWatt SECULIFE ST PRO Manual Download Page 90

90

GMC-I Messtechnik GmbH

11.1

List of error messages

Error Messages

Possible Causes

Corrective Measures

Mains Connection Errors

–

Protective conductor PE at the 
mains outlet at which the test 
instrument is being operated is 
conducting voltage! This detection 
function makes use of the metal-
lized START/STOP key on the test 
instrument. In order for detection to 
function correctly, it must be possi-
ble to establish reference to earth 
potential via the user’s finger.

Note

If the user’s finger is insulated 
from the key when it’s 
pressed, this error message 
may occur although the instal-
lation is OK (see “Automatic 
Recognition of Mains Con-
nection Errors” on page 13).

➭

Please remove the test instru-
ment’s mains plug from this outlet 
and arrange to have the outlet/in-
stallation inspected by a qualified 
electrician without delay. Do not 
operate any other devices at this 
electrical outlet before this inspec-
tion has been completed.

➭

In order to ensure that detection 
functions reliably, repeat the inter-
ference voltage test and observe 
the following tips: 
– Unplug all USB devices from the 

test instrument’s USB ports.

– Remain in contact with a 

grounded object while pressing 
the START/STOP key 
(e.g. a heating pipe).

– Do not contact the START/STOP 

key with an object or while wearing 
gloves.

PE connection not detected (at the 
outlet at which the test instrument is 
being operated):

–

If the installation is defective!

–

In the case of special types of TT 
systems; detection may fail in this 
case.

–

If the test instrument is being oper-
ated in an IT system

➭

If the test instrument is being oper-
ated in an IT system: 
Acknowledge the question by 
pressing 

 – the IT system option 

is activated in this case.

➭

If it’s not an IT system: remove the 
mains plug from the outlet and in-
spect the installation without delay!

➭

If it’s a TT system without neutral 
conductor, press 

; direct leak-

age current measurements are 
possible. 
(Please make absolutely sure that 
direct leakage current measure-
ments are possible in your current 
mains type!)

As opposed to the previously used 
mains connection, PE was detected 
while the IT system option was acti-
vated in setup.

➭

Operation in an IT system: Re-
spond to the question by pressing 

. 

The IT system option remains ac-
tive as a result.

➭

Operation in TN or TT system: Re-
spond to the question by pressing 

. The IT system option is deacti-

vated as a result.

Line frequency is less than 48 or 
greater than 62 Hz

➭

PE detection does not function in 
this case: select 

 or 

 depend-

ing on whether or not the utilized 
system is an IT system.

Summary of Contents for SECULIFE ST PRO



















































































































Reviews:

No comments