manualshive.com logo in svg

Gossen MetraWatt SECULIFE ST PRO, Manual, Page: 92 / 114

Share
Download
Gossen MetraWatt SECULIFE ST PRO Manual Download Page 92

92

GMC-I Messtechnik GmbH

Connection Error at the Test Socket

–

Test probe P1 isn’t connected.

or

–

The test instrument’s 10 A/25 A 
transformer is overheated.

or

–

One of the fuses has blown (fuse 
holder in close proximity to the 
mains input).

➭

Repeat measurement with probe P1 
connected.

➭

Check the fuses and replace if nec-
essary.

➭

Select a different test current (e.g. 
200 mA) or wait until the trans-
former has cooled down and then 
repeat the measurement.

Attention!

!

The 10 A/25 A measurement 
isn’t suitable for continuous 
operation!

–

A short-circuit has been detected 
at the test socket between L and 
N.

➭

Determine whether or not the de-
vice under test is defective.

➭

In the case of DUTs which are intended 
for operation at an outlet that’s pro-
tected with a 16 A fuse, a short-circuit 
may be detected under certain circum-
stances if, for example, they include a 
PTC thermistor (e.g. large floodlights). 
Be sure to use a 3-phase test adapter 
in order to test devices of this sort (e.g. 
the AT3-IIIE).

➭

You can skip this short-circuit mes-
sage at your own risk and place 
the device under test into service. 
Any damage resulting from skip-
ping this warning is excluded from 
the guarantee!

–

A device under test, whose leak-
age current (measured by means 
of the differential current method) 
exceeds the limit value specified in 
SETUP, is connected to the test 
instrument and has been started 
up.

➭

If the device under test normally 
generates a leakage current of 
greater than 10 mA (e.g. large 
heaters), temporarily increase the 
“residual current protection” value 
selected in setup to 30 mA and try 
again.

➭

If values of this magnitude are not 
to be expected for the respective 
device under test, or if the “residual 
current protection” value has al-
ready been set to 30 mA in Setup, 
there may be a ground fault at the 
DUT.

–

The fuse for the test socket’s L 
conductor has blown 
(fuse link 2).

➭

Disconnect the test instrument 
from the mains and inspect the 
fuses next to the it’s mains con-
nection.

Error Messages

Possible Causes

Corrective Measures

Summary of Contents for SECULIFE ST PRO



















































































































Reviews:

No comments