GILES GEF-400 Operation & Service Manual Download Page 83

Page: 83 / 115

GEF-VH Series Fryers Only

Ventless Hood

EAC

7.1.5

EAC Filter Cell Removal

7.1.4

Baffle Filter Cleaning

Typically, the Baffle Filter needs to be cleaned daily. Wash Filter in sink with a mild degreaser and warm water.

Rinse and dry thoroughly; reinstall in the unit.

Be sure Filter is completely dry before re-installing into the Hood.

Never place wet or damp Baffle Filter into the hood!

The Baffle Filter may be washed in the dishwasher.

1. Unlatch Filter Access Cover and lift off.
2. Grasp EAC Filter Cell handle and pull it straight out, on a slight upward angle.

The Baffle Filter has sharp exposed edges, which may cause cuts; use due caution when

handling and cleaning. Use of heavy duty rubber gloves is advised.

Summary of Contents for GEF-400




















































































































Search results

Summary of Contents for GEF-400

Reviews:

Related manuals for GEF-400

Brands by name

Popular brands

GILES GEF-400, Operation & Service Manual

Search results

Summary of Contents for GEF-400

Reviews:

Related manuals for GEF-400

Brands by name

Popular brands