GILES GEF-400 Operation & Service Manual Download Page 46

Page: 46 / 115

Fryer Operation

The following section describes operational procedures for

Giles Model GEF & GEF-VH Electric Fryers

GEF & GEF-VH Series Fryers

• Turn off the Fryer power switch and the supply power at main electrical panel, or remove plug for receptacle

before cleaning or performing maintenance.

•

DO NOT

wash down the Fryer interior or exterior with water spray, or any other pressure-type washing

equipment.

• Failure to comply with

DANGER

notices will result in serious injury, even death, damage to equipment or

property and void the factory warranty

•

DO NOT

use or store flammable liquids, or materials that produce flammable vapors, in the vicinity of this or

any other appliance!

•

DO NOT (or ALLOW OTHERS) for any reason, stand or step onto the top of the appliance

. Cooking

oil in Fryers can be

EXTREMELY HOT (excess of 330

F [166°C]).

Bodily contact will cause extremely

serious injury. Lids used to sometimes cover cooking vats/pots are not designed to, and

WILL NOT

support the weight of a person.

• Failure to comply with

WARNING

notices could result in serious injury, even death; damage to equipment

and/or property and will void the factory warranty.

• Be sure the Fryer is positioned in a stable, safe location with the casters in the locked position.
• Consult an electrician to be certain that all electrical specifications have been met and the unit is properly

grounded. A wiring diagram is provided with the unit to aid an electrician.

• Due to the high temperature of cooking oil in the Fryer during cooking, it is extremely important that the User

exercise due caution when operating this equipment to avoid personal injury.

To avoid personal injury, it is

recommended that thermal hand protection (gloves or mitts) be worn while tended the appliance

• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental

capabilities, or lack of experience and knowledge, unless they have been given adequate instruction and/or

supervision concerning its use by a person responsible for their safety. Children should be supervised, or

otherwise restricted, to ensure they do not play with or around this appliance.

Summary of Contents for GEF-400




















































































































Search results

Summary of Contents for GEF-400

Reviews:

Related manuals for GEF-400

Brands by name

Popular brands

GILES GEF-400, Operation & Service Manual

Search results

Summary of Contents for GEF-400

Reviews:

Related manuals for GEF-400

Brands by name

Popular brands