GILES GEF-400 Operation & Service Manual Download Page 87

Page: 87 / 115

GEF-VH Series Fryers Only

Ventless Hood

7.1.10

Charcoal Filter Removal & Installation

Switch must be actuated by

the filter when installed.

7.1.11

Charcoal Filter Maintenance

IMPORTANT! The Charcoal Filter cannot be cleaned and reused; ONLY replace. It is a one-use, consumable filter

that must be replaced periodically. Never attempt to clean the Charcoal Filter; damage to the equipment could

result. Typical replacement cycle is 30 to 40 days, depending on usage.

Replace the Charcoal Filter with Giles Part No.

30248

Failure to use Giles OEM Replacement Parts and Filters may void the factory warranty.

1. Unlatch Filter Access Cover and lift off.
2. Grasp Charcoal Filter and pull straight out, at an slight

upward angle.

Note airflow arrow on

label; blue fiber-fill side UP.

1. Install with blue fiber-fill side facing

2. Align in guide Channels, slide straight into

Hood. Filter must fit flush with Hood front.

Summary of Contents for GEF-400




















































































































Search results

Summary of Contents for GEF-400

Reviews:

Related manuals for GEF-400

Brands by name

Popular brands

GILES GEF-400, Operation & Service Manual

Search results

Summary of Contents for GEF-400

Reviews:

Related manuals for GEF-400

Brands by name

Popular brands