GILES GEF-400 Operation & Service Manual Download Page 25

Page: 25 / 115

GEF & GEF-VH Series Fryers

Installation

2.11

Changing the Door Swing

Certain situations may require that the door swing direction be reversed to allow easier access to the lower cabinet.

This procedure is described below.

1. Disconnect power.

2. Remove (4) screws

①

on the left side of the lower

cabinet.

3. While supporting door; remove (4) screws

②

holding the top and bottom hinges to the Cabinet;

remove Door.

4. Remove the plastic washer

③

from the bottom

hinge and save.

5. Flip the top-right Hinge

④

, move it to the bottom-

Lief Cabinet side and attach; do not tighten. Place

the plastic Washer

③

on the hinge pin.

6. Flip the Cabinet Door and hang on the bottom-left

Hinge Pin.

7. Flip the bottom-right Hinge

⑤

, move it the top-

left. Insert pin into Door, then attach Hinge to

Cabinet; do not tighten.

8. Check door swing and levelness; adjust as needed

and securely tighten all hinge screws.

9. Install (4) screws removed in Step #2 to fill holes on

right side of the Cabinet.

10. Reconnect power.

11.Order a new

Quick Reference Door Label (Part No.

60802)

⑥

and apply over existing label.

Not shown

Summary of Contents for GEF-400




















































































































Search results

Summary of Contents for GEF-400

Reviews:

Related manuals for GEF-400

Brands by name

Popular brands

GILES GEF-400, Operation & Service Manual

Search results

Summary of Contents for GEF-400

Reviews:

Related manuals for GEF-400

Brands by name

Popular brands