GILES GEF-400 Operation & Service Manual Download Page 20

Page: 20 / 115

GEF & GEF-VH Series Fryers

Installation

2.4.1

Conduit Routing

2.4

Electrical Connections

1. As needed, install appropriate sized circuit breaker in main electrical panel. See

Table 2.3

2. Connect 1-1/4” flexible conduit from main electrical panel to the Fryer. Attach conduit to rear of the Fryer

with appropriate conduit fittings. Allow enough length so that the Fryer can be moved easily for cleaning and

servicing. See

Figure 2.4.1

3. Open Fryer Cabinet Door and remove Service Entrance Box Cover. See

Figure 2.4.2

4. Route appropriately sized power wires from the circuit breaker in the main panel through the wire run inside

Cabinet wall to the front Service Box.

5. Connect power wires to the appropriate Terminal Blocks in the Service Entrance Box. See

Figure 2.4.2

6. Reinstall Service Entrance Box Cover and close the cabinet door.

1-1/4” Straight or 90°

Connector

1-1/4” Flexible

Conduit

Main Electrical

Panel

NOTE:

Electrical installation materials (breakers, conduit, fittings, wire, etc.) and installation labor shall be supplied by

the customer. Work should be performed by a qualified electrician, or service technician.
Installation must comply with local code requirements. Giles is not responsible for code compliance with regard

to installation and use of this appliance.

Summary of Contents for GEF-400




















































































































Search results

Summary of Contents for GEF-400

Reviews:

Related manuals for GEF-400

Brands by name

Popular brands

GILES GEF-400, Operation & Service Manual

Search results

Summary of Contents for GEF-400

Reviews:

Related manuals for GEF-400

Brands by name

Popular brands