GILES GEF-400 Operation & Service Manual Download Page 80

Page: 80 / 115

GEF-VH Series Fryers Only

Ventless Hood

The following section applies

ONLY

to GEF-VH Ventless Hood Fryers. It describes operation and maintenance of the

Fryer Integral Ventless Hood System. It is

important

that all Filters are properly installed, and that the Filter Access

Cover is in place and securely latched before attempting to operate the appliance. See

Section 5.1.9.2, Start-up

Ventless Fryer

IMPORTANT! The appliance will NOT power-up if the Filter Access Cover is missing, or ajar. The sides of this

Cover must seat flush against the Hood front and the pin on the right-hand edge must engage the interlock

switch inside the Hood wall.

7.1

Filters

This section discusses each Filter in the Ventless Hood system and describes removal, installation, cleaning

procedures, and specific alarm conditions that occur if the filter system is not properly maintained. Maintenance

and cleaning must be performed as prescribed to keep the Hood operating at peak performance to remove grease-

laden vapor produced by the Fryer.

7.1.1

Ventless Hood Filter Table

Filter

When to Clean or

Replace

How to Remove

How to Clean

How to install

Baffle Filter

Clean Daily

Section7.1.2

Section 7.1.5

Section 7.1.3

EAC Filter Cell

Clean Daily

Section 7.1.6

Section 7.1.9

Section 7.1.7

Charcoal Filter

Replace approx.

every 30 days,

P/N 30248

Section 7.1.10

REPLACE ONLY

Cannot be Cleaned

Section 7.1.11

Summary of Contents for GEF-400




















































































































Search results

Summary of Contents for GEF-400

Reviews:

Related manuals for GEF-400

Brands by name

Popular brands

GILES GEF-400, Operation & Service Manual

Search results

Summary of Contents for GEF-400

Reviews:

Related manuals for GEF-400

Brands by name

Popular brands