GILES GEF-400 Operation & Service Manual Download Page 21

Page: 21 / 115

GEF & GEF-VH Series Fryers

Installation

2.5

Ventilation of Non-Ventless Fryer

2.6

Ventless Hood Clearances (VH Model)

GEF Ventless Hood Fryers are equipped with an exhaust air diverter that directs exhaust air horizontally (side and

rear). The minimum clearance from the top of the diverter to the ceiling is 0” [0 mm], however it is recommended

that adequate space be provided to allow easy movement of the unit if required. The area around the sides and

rear of the diverter must remain free of obstruction to allow proper air flow.

DETAIL A

2.4.2 Service Box Connections

Terminal Blocks

Service Entrance Box

Power Wires from Main

Breaker Panel

Consult a professional ventilation or HVAC company for assistance in determining whether existing systems are

sufficient to accommodate this equipment, or in designing a ventilation hood system to comply with code

requirements.

NOTE:

Guidelines and codes for ventilation system requirements differ from locale to locale. Always consult the local

Authorities Having Jurisdiction (AHJ)

to ensure compliance.

Summary of Contents for GEF-400




















































































































Search results

Summary of Contents for GEF-400

Reviews:

Related manuals for GEF-400

Brands by name

Popular brands

GILES GEF-400, Operation & Service Manual

Search results

Summary of Contents for GEF-400

Reviews:

Related manuals for GEF-400

Brands by name

Popular brands