manualshive.com logo in svg

Gilera Runner RST 50 SP, Service Station Manual, Page: 92 / 183

Share
Download
Gilera Runner RST 50 SP Service Station Manual Download Page 92

Refitting the crankshaft bearings

- This operation requires assembly by temperature

- Dip the bearings in oil bath when this is still cold.

Avoid contact between bearings and container.

- Use an appropriate amount of oil (approx.1 l)

- Gradually heat the container with a thermal gun

until the oil temperature reaches approx. 150°.

- Check the temperature using a multimeter provi-

ded with thermal probe

N.B.

IF THE BEARINGS WERE IMMERSED INTO HOT OIL, THEY
WOULD BE IMMEDIATELY DAMAGED.

- Place the crankshaft on the special support

- Alternately introduce the 2 bearings to insert

them home.

- If required, use a specific pipe to ensure their in-

sertion.

N.B.

THIS OPERATION SHOULD BE PERFORMED QUICKLY
AND WITH PRECISE MOVES. OTHERWISE, START OVER.

Specific tooling

020265Y

 

Bearing fitting base

008119Y009

 

Tube to assemble shafts and

axles

Engine

Runner RST 50 SP

ENG - 92

Summary of Contents for Runner RST 50 SP
























































































































































































Reviews:

No comments