Gilera Runner RST 50 SP Service Station Manual Download Page 107

Page: 107 / 183

Refitting the rear wheel

- On refitting, tighten to the prescribed torque in a cross over pattern.

Locking torques (N*m)

Rear wheel:

20 - 25 Nm

Shock absorbers

Removal

To replace the shock absorber, simply remove the

door to access the tool bag and remove the shock

absorber / chassis nut. Then remove the shock

absorber / engine anchor bolt.

Refitting

When refitting, tighten the shock absorber/frame anchorage nut and the shock absorber/engine pin at

the prescribed torque.

Locking torques (N*m)

Shock absorber/frame nut torque

20 to 25 Nm

Shock absorber/engine pin torque

33 to 41 N·m

Centre-stand

Expulsion of kickstand bracket fastening pin

Runner RST 50 SP

Suspensions

SUSP - 107

Summary of Contents for Runner RST 50 SP
























































































































































































Search results

Summary of Contents for Runner RST 50 SP

Reviews:

Gilera Runner RST 50 SP, Service Station Manual, Page: 107 / 183

Search results

Summary of Contents for Runner RST 50 SP

Reviews: