manualshive.com logo in svg

Gilera Runner RST 50 SP, Service Station Manual, Page: 114 / 183

Share
Download
Gilera Runner RST 50 SP Service Station Manual Download Page 114

Removal

Proceed as follows:

- Remove the front calliper.

- Loosen the two pins shown in the figure that lock

the two pads.

- Remove the pads, being careful with the pad

spring clamp.

- Check the thickness of the pads.

Characteristic

Minimum value

1.5 mm

See also

Front

brake calliper

Refitting

To fit, proceed as follows:

- Insert the two pads in the callipers.

- Screw the two pad lock pins to the correct torque, and apply the recommended product.

- Fit the calliper on its support, tightening the two screws to the prescribed torque.

N.B.

IF IT IS NOT POSSIBLE TO CORRECTLY POSITION THE CALLIPER ON THE DISC DURING FIT-
TING, GENTLY EXPAND THE PADS.

Recommended products

Loctite 243

 

Medium strength threadlock

Loctite 243 medium-strength threadlock

Locking torques (N*m)

Screw tightening calliper to the support

 

20 ÷ 25

 

Pad fastening pin

 

19.6 ÷ 24.5

Braking system

Runner RST 50 SP

BRAK SYS - 114

Summary of Contents for Runner RST 50 SP
























































































































































































Reviews:

No comments