manualshive.com logo in svg

Gilera Runner RST 50 SP, Service Station Manual, Page: 173 / 183

Share
Download
Gilera Runner RST 50 SP Service Station Manual Download Page 173

Front wheel

F

RONT

 

WHEEL

Code

Action

Duration

1

002041

Front brake disc - Replacement

2

003040

Front wheel bearings - Replacement

3

003037

Front wheel rim- Replacement

4

003047

Front tyre - replace

5

004123

Front wheel - Replacement

6

003038

Front wheel axle - Replacement

7

005089

Tone wheel - Replacement

Grease tone wheel or drive

Please take note that the code has been intro-

duced:

900001 - Tone wheel / drive greasing - 15'.

Never mistake the codes 002011 (movement sen-

sor replacement) and 005089 (tone wheel replace-

ment) in the event of noise of the indicated

components. The grease recommended is TUTE-

LA MRM 2 (soap-based lithium grease with Mo-

lybdenum disulphide).

In the following points we indicate with an arrow

the area to be greased (1 - Drive, 2 - Tone wheel)

Runner RST 50 SP

Time

TIME - 173

Summary of Contents for Runner RST 50 SP
























































































































































































Reviews:

No comments