Gilera Runner RST 50 SP Service Station Manual Download Page 101

Page: 101 / 183

Removing the front wheel

Refitting the front wheel

- When refitting, pay attention in repositioning the odometer drive correctly.

Locking torques (N*m)

Wheel axle nut

45 ÷ 50

Wheel axle clamp screws

6 - 7 Nm

Handlebar

Removal

- Remove the front handlebar cover.

- Remove the rear handlebar cover.

- After removing the transmissions and discon-

necting the electrical terminals, remove the bolt

«A» and the handlebar

- Check all components and replace faulty parts.

N.B.

IF THE HANDLEBAR IS BEING REMOVED TO REMOVE
THE STEERING, TILT THE HANDLEBAR FORWARD TO
AVOIDING DAMAGING THE TRANSMISSIONS.

Refitting

When refitting, tighten to the prescribed torque and

apply the recommended grease to the threaded

cone.

Recommended products

AGIP GREASE PV2

Grease for control levers

on the engine

White anhydrous-calcium based grease to protect

roller bearings; temperature range between -20 °

C and +120 °C; NLGI 2; ISO-L-XBCIB2

Locking torques (N*m)

Locking torque:

65 to 70 N•m

Front fork

Runner RST 50 SP

Suspensions

SUSP - 101

Summary of Contents for Runner RST 50 SP
























































































































































































Search results

Summary of Contents for Runner RST 50 SP

Reviews:

Gilera Runner RST 50 SP, Service Station Manual, Page: 101 / 183

Search results

Summary of Contents for Runner RST 50 SP

Reviews: