manualshive.com logo in svg

Gilera Runner RST 50 SP, Service Station Manual, Page: 112 / 183

Share
Download
Gilera Runner RST 50 SP Service Station Manual Download Page 112

4. Fixed plate

5. Floating body

6. Piston

7. Piston sealing rings

8. Guide protection rubbers

9. Brake pad check spring

10. Pads

CAUTION

ALL THE SEALS AND GASKETS MUST BE REPLACED EV-
ERY TIME THE CALLIPER IS SERVICED.

Locking torques (N*m)

Calliper tightening screw

 

24 ÷ 27

 

Brake fluid

pipe-calliper fitting

 

19 ÷ 24

Refitting

•

Refit the pincer on the support and

tighten the screws at the prescribed

torque.

•

Refit the tube complete with fitting with

new copper gaskets.

•

Bleed the air from the system.

Locking torques (N*m)

Brake fluid tube calliper

 

20 ÷ 25 Nm

 

Fastening

screws calliper to the crankcase

 

20 - 25

 

Oil bleed

screw

 

7 to 10 Nm

Front brake disc

Removal

- Remove the front wheel loosening the axle

clamp.

-Remove the six fastenings of the disc.

Braking system

Runner RST 50 SP

BRAK SYS - 112

Summary of Contents for Runner RST 50 SP
























































































































































































Reviews:

No comments