Gilera Runner RST 50 SP Service Station Manual Download Page 102

Page: 102 / 183

Removal

- Remove the front brake calliper.

- Remove the odometer cable from the reduction

gear box.

- Remove the front mudguard.

- Remove the handlebar.

After removing the steering ring-nut using the spe-

cial tool, lean the vehicle on one side and extract

the steering tube.

Specific tooling

020055Y

Wrench for steering tube ring nut

See also

Handlebar
Front mudguard
Front

brake calliper

Overhaul

Removing damper

- Remove screw 1 fixing the screw to the stem and

remove the stanchion heating it if necessary with

the specified heater, then remove sealing ring 2

and seeger 3.

- Using nut 4, remove the spring stem and bushing.

The damper is an integral part of the stem and

cannot therefore be overhauled, so if you need to

work on the damper (loss of fork oil), carry out the

operations mentioned above and replace the

shock absorber-stem unit.

When refitting, tighten to the prescribed torque and

apply the recommended grease to the threadlock

nut.

Specific tooling

020150Y

Air heater support

020151Y

Air heater

Recommended products

Loctite 243

Medium strength threadlock

Suspensions

Runner RST 50 SP

SUSP - 102

Summary of Contents for Runner RST 50 SP
























































































































































































Search results

Summary of Contents for Runner RST 50 SP

Reviews:

Gilera Runner RST 50 SP, Service Station Manual, Page: 102 / 183

Search results

Summary of Contents for Runner RST 50 SP

Reviews: