manualshive.com logo in svg

Gilera Runner RST 50 SP, Service Station Manual, Page: 110 / 183

Share
Download
Gilera Runner RST 50 SP Service Station Manual Download Page 110

Rear brake calliper

Removal

- Disconnect the hydraulic union collecting the oil

in an appropriate container.

- Loosen the two support calliper clamps.

Front brake calliper

Removal

•

Check that the brake piping, gasket

and fitting are in good condition. If you

see any oil on the brake calliper and/on

the components of the system, it is

necessary to replace them.

•

- Disconnect the oil line from the cal-

liper, collecting the oil in a container.

•

- Remove the two clamps highlighted

in the diagram.

Overhaul

Proceed as follows:

1) remove the two male hexagonal screws (1) and

take out the two pads (10);

2) remove the two male hexagonal screws (2) and

remove the reaction plate (3);

3) take out the fixed plate (4) from the guide;

4) remove the internal elements from the floating

body (5) with the help of short blows of com-

Braking system

Runner RST 50 SP

BRAK SYS - 110

Summary of Contents for Runner RST 50 SP
























































































































































































Reviews:

No comments