manualshive.com logo in svg

Gilera Runner RST 50 SP, Service Station Manual, Page: 69 / 183

Share
Download
Gilera Runner RST 50 SP Service Station Manual Download Page 69

Removing the driven pulley

- Lock the clutch bell housing with the specific tool.

- Remove the nut, the clutch bell housing and the

whole of the driven pulley assembly.

N.B.

THE UNIT CAN ALSO BE REMOVED WITH THE DRIVE
PULLEY MOUNTED.

Specific tooling

020565Y

 

Flywheel lock calliper spanner

Inspecting the clutch drum

- Check that the clutch bell is not worn or damaged.

- Measure the inner diameter of the clutch bell.

Characteristic

Clutch bell diameter/standard value

Ø 107+0.2 +0 mm

Clutch bell diameter/max. value allowed after
use

Ø 107.5 mm

Eccentricity measured /max.

0.20 mm

Removing the clutch

- Equip the tool with long pins screwed into position

«

A

» from the outside, insert the entire driven pulley

in the tool and put the central screw under stress.

CAUTION

THE TOOL WILL BE DEFORMED IF THE CENTRAL SCREW
IS TIGHTENED UP TOO FAR.

Runner RST 50 SP

Engine

ENG - 69

Summary of Contents for Runner RST 50 SP
























































































































































































Reviews:

No comments