manualshive.com logo in svg

Gilera Runner RST 50 SP, Service Station Manual, Page: 73 / 183

Share
Download
Gilera Runner RST 50 SP Service Station Manual Download Page 73

Refitting the driven half-pulley bearing

- Fit a new ball bearing with the specific tool.

- Fit the ball bearing retention snap ring.

- Fit the new roller bearing with the wording visible

from the outside.

CAUTION

PROPERLY SUPPORT THE HALF-PULLEY TO PREVENT
DAMAGE TO THE THREADED END WHILE THE BEARINGS
ARE BEING FITTED.

Specific tooling

020376Y

 

Adaptor handle

020456Y

 

Ø 24 mm adaptor

020362Y

 

12 mm guide

020171Y

 

Punch for Ø 17 mm roller case

Inspecting the clutch spring

- Check that the contrast spring of the driven pulley

does not show signs of deformation

- Measure the free length of the spring

Characteristic

Standard length

118 mm

Minimum length allowed after use

XXXX

Refitting the clutch

- Preassemble the driven pulley group with spring,

sheath and clutch.

- Position the spring with the sheath

- Insert the components in the tool and preload the

spring being careful not to damage the plastic

sheath and the end of the threaded bar.

Runner RST 50 SP

Engine

ENG - 73

Summary of Contents for Runner RST 50 SP
























































































































































































Reviews:

No comments