manualshive.com logo in svg

Gilera Runner RST 50 SP, Service Station Manual, Page: 32 / 183

Share
Download
Gilera Runner RST 50 SP Service Station Manual Download Page 32

Replacement

-Remove the oil cap «

A

».

- Unscrew the oil cap «

B

» and drain out all the oil.

- Screw the cap back on and fill up the hub with the

required oil.

Characteristic

Rear hub oil

Quantity: approx. 75 cm³

Air filter

-Remove the cap of the purifier, unscrewing the six

clamping screws and removing the filter.

Cleaning

:

-Wash with water and neutral soap.

- Dry with a clean cloth and short blasts of com-

pressed air.

-Saturate with a 50% mixture of gasoline and oil.

-Drip dry the filter and then squeeze it between the

hands without wringing.

-Let it dry and refit it again.

CAUTION

NEVER RUN THE ENGINE WITHOUT THE AIR FILTER,
THIS WOULD RESULT IN AN EXCESSIVE WEAR OF THE
PISTON AND CYLINDER.

Recommended products

AGIP FILTER OIL

 

Oil for air filter sponge

Mineral oil with specific additives for increased ad-

hesiveness

Maintenance

Runner RST 50 SP

MAIN - 32

Summary of Contents for Runner RST 50 SP
























































































































































































Reviews:

No comments