manualshive.com logo in svg

Gilera Runner RST 50 SP, Service Station Manual, Page: 67 / 183

Share
Download
Gilera Runner RST 50 SP Service Station Manual Download Page 67

this section is under processing

Automatic transmission

Transmission cover

- Loosen the 15 screws and remove the transmis-

sion cover with the aid of a mallet.

N.B.

THE CRANKCASE IS SLIGHTLY BLOCKED BY THE TIGHT
FIT BETWEEN THE SHAFT OF THE DRIVEN HALF-PULLEY
AND THE BEARING HOUSED ON THE CRANKCASE.

Kickstart

- Remove the seeger ring located on the exterior

of the crankshaft.

- Dismantle the dog gear from its seat, slackening

the tension that the toothed sector applies to it by

means of the spring; to do this, it is necessary to

rotate the toothed sector slightly (see the figure).

CAUTION

WHILE REMOVING THE TOOTHED SECTOR, BE VERY
CAREFUL OF THE SPRING TENSION: IT COULD CONSTI-
TUTE A HAZARD FOR THE OPERATOR.

- Remove the screws shown in the figure and re-

move the engine starting lever.

- For the assembly, work in reverse and tighten the

screws to the prescribed torque..

Locking torques (N*m)

Starter lever replacement

 

12 to 13 Nm

Runner RST 50 SP

Engine

ENG - 67

Summary of Contents for Runner RST 50 SP
























































































































































































Reviews:

No comments