manualshive.com logo in svg

Gilera Runner RST 50 SP, Service Station Manual, Page: 81 / 183

Share
Download
Gilera Runner RST 50 SP Service Station Manual Download Page 81

Refitting the stator

- Refit the stator and flywheel proceeding in the

inverse direction, tightening the studs to the pre-

scribed torque.

THREAD THE CABLE OF THE STATOR INTO THE SPECIF-
IC HOUSING OF THE CRANKCASE AND MAKE SURE
THAT IT IS LOCKED BY THE TAB OF THE RETURN LINE
OF THE COOLING SYSTEM.

Locking torques (N*m)

Pick-up screws

 

3 ÷ 4

 

Stator screws

 

3 ÷ 4

Refitting the flywheel cover

•

Fit the rubber seal on the flywheel con-

nector and around the inlet coolant

hose.

•

Keeping the flywheel connector rubber

clamp on the coolant inlet hose, refit

the flywheel cover paying attention in

inserting the strap in the groove.

•

Tighten the 4 studs, noting that the two

longer golden screws are inserted in

the 2 top holes and are also responsi-

ble for restraining the secondary air-

box.

Flywheel and starting

Runner RST 50 SP

Engine

ENG - 81

Summary of Contents for Runner RST 50 SP
























































































































































































Reviews:

No comments