Troubleshooting
10-3
Check NIBP
NIBP measurement affected by low
blood pressure and pulsation, or a
change in patient's condition.
•
Check the patient status.
•
Check the measurement setup.
•
Check the cuff.
Check sample gas out
Sample gas outlet is blocked.
•
Remove blockage from the sample
gas outlet.
Check SpO2 probe
SpO
2
: There is no detectable SpO
2
signal, the sensor is faulty or it is
detached from the patient.
•
Check the sensor and connections.
Cuff loose
Cuff is not attached to the patient or it
is too loose. The hose is not connected
to the module.
•
Check cuff and hose.
Cuff occlusion
Tubes or hose are kinked.
•
Check tubes and hose.
Cuff overpressure
Cuff is squeezed during measurement
and pressure safety limits are
exceeded.
•
Check cuff, hose and tubes.
•
Restart measurement.
measurement off
Leads have been disconnected for 15
minutes for impedance respiration
check or have just been connected
(<15 seconds ago).
•
Reconnect the leads or wait to
continue the measurement.
EEPROM error or EPROM error Faulty EEPROM circuit on the CPU
board, or failure in CPU software
memory.
•
Call service to replace CPU.
Faulty ECG cable
The ECG cable is defective.
The ECG cable may be electrically
damaged or the connectors are wet.
•
Change the ECG cable and the lead
set.
•
Change the ECG module if the
module connector is wet. Keep the
connectors dry.
•
Avoid excessive use of liquids when
cleaning cables and connectors.
Gas measurements removed
•
Reconnect the N-FREC or N-FCREC
module if you want to restart the
CO
2
measurement.
Identical modules
There are two identical modules
measuring the same parameter.
•
You are trying to use two or more
E-PSM(P)W modules or two or more
N-Fx modules at the same time.
You can only use one E-PSM(P)W
and/or one N-Fx module at a time.
Remove extra modules.
Infl. limits! Check setup
Adult or child cuff is used but infant
inflation mode is selected.
•
Check cuff and inflation limits.
InvBP’s not zeroed
One or both InvBP channels have not
been zeroed.
•
Zero the channel indicated or zero
both channels.
Message
Explanation
What to do
Summary of Contents for b30
