Fuji Xerox DocuPrint C525 A User Manual Download Page 40 | Manualshive

Page: 40 / 96

background image

40

4 Setting on the Control Panel

Admin Menu

This menu contains five sub menus, [Network], [Parallel], [System Settings], [Maintenance
Mode], and [Panel Settings].

Network

Specifies the settings for the network. The settings with the suffix “*” in the following table
are displayed when the optional network expansion card is installed.

Note
• The settings in the [Network] cannot be set when entering this menu during printing.
• You need to restart the printer to activate the new settings. After making the settings, switch off the

printer and then switch it on again.

Item

Description

Ethernet

Specifies the communication speed and the modes of Ethernet.
• [Auto] (default)

Automatically changes between 10Base half, 10Base full, 100Base half, and
100Base full.

• [10Base Half]
• [10Base Full]
• [100Base Half]
• [100Base Full]

TCP/IP

Specifies the settings to use the TCP/IP protocol.

Get IP Address

Set the IP address acquisition method.
• [DHCP/Autonet] (default)

Automatically sets the IP address.

• [BOOTP]

Uses BOOTP to set the IP address automatically.

• [RARP]

Uses RARP to set the IP address automatically.

• [DHCP]

Uses DHCP to set the IP address automatically.

• [Panel]

You can set the IP address manually by entering it on the operator panel.

IP Address,
Subnet Mask,
Gateway Address

These items are used to check the addresses that have been obtained automatically or
to specify addresses manually. Enter the address in the format of xxx.xxx.xxx.xxx. You
can specifies values in the range of 0 to 255 for xxx.

Important

• To set addresses manually, set the [Get IP Address] to [Panel].
• IP addresses are managed in the entire network. An incorrect IP address may affect

the whole network. For the addresses you need to set manually, contact your network
administrator.

Protocol

Set [On] when using the protocol. When [Disable] is selected, the protocol cannot be
activated.
• [LPD] (default: [Enable])
• [Port9100] (default: [Enable])
• [IPP] (default: [Enable])*
• [SMB TCP/IP] (default: [Enable])*
• [SMB NetBEUI] (default: [Enable])*
• [FTP] (default: [Enable])
• [NetWare] (default: [Enable])*
• [SNMP UDP] (default: [Enable])
• [SNMP IPX] (default: [Enable])*
• [StatusMessenger] (default: [Enable])
• [Internet Services] (default: [Enable])

«
...
38
39
40
41
42
...
»

Summary of Contents for DocuPrint C525 A

































































































Reviews:

No comments

Related manuals for DocuPrint C525 A

Brand: Datecs Pages: 73

Brand: Datamax Pages: 12

E-Class Mark II

Brand: Datamax Pages: 40

Brand: Datamax Pages: 46

Brand: Nantian Electronics Pages: 4

Brand: Oki Pages: 1

imageRUNNER 5075

Brand: Canon Pages: 502

imageRUNNER 5075

Brand: Cannon Pages: 268

Brand: Oki Pages: 40

Brand: Dascom Pages: 146

Brand: Wang Pages: 181

Brand: Axis Pages: 66

Brand: A&D Pages: 31

Brand: Star Micronics Pages: 130

Brand: Xiamen Sojet Electronics Pages: 37

Brand: Konica Minolta Pages: 36

Stylus Photo RX640 series

Brand: Epson Pages: 56

Stylus Photo PX830FWD

Brand: Epson Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands