Fuji Xerox DocuCentreS2320 User Manual Download Page 227

Page: 227 / 257

Error Code

227

roblem

lvin

093-959

[Cause]

An error occurred with the drum cartridge.

[Remedy] Replace the drum cartridge. Contact your local Fuji Xerox

representative or sales representative.

Refer to "Replacing the Toner Cartridge" (P.179).

116-317
116-321
116-323

[Cause]

An error occurred.

[Remedy] Switch off the machine power, make sure that the display is blank,

and then switch on the machine power. If the same message is
displayed again, contact our Customer Support Center.

116-324

[Cause]

An error occurred.

[Remedy] The machine will automatically recover. Wait for a while, and try

again.

116-334
116-377
116-390

[Cause]

An error occurred.

[Remedy] Switch off the machine power, make sure that the display is blank,

and then switch on the machine power. If the same message is
displayed again, contact our Customer Support Center.

116-747

[Cause]

Unable to complete scanning due to the scanning area being too
small.

[Remedy] Decrease the value of the Edge Erase or reduce the zoom ratio.

117-319
117-320
117-321
117-329
117-332
123-314

[Cause]

An error occurred.

[Remedy] Switch off the machine power, make sure that the display is blank,

and then switch on the machine power. If the same message is
displayed again, contact our Customer Support Center.

127-396

[Cause]

Failed to create an e-mail data.

[Remedy] Press the control panel's <Stop> button, and try again.

Error Code

Cause and Remedy

Summary of Contents for DocuCentreS2320

































































































































































































































































Search results

Summary of Contents for DocuCentreS2320

Reviews:

Related manuals for DocuCentreS2320

Brands by name

Popular brands

Fuji Xerox DocuCentreS2320, User Manual

Search results

Summary of Contents for DocuCentreS2320

Reviews:

Related manuals for DocuCentreS2320

Brands by name

Popular brands