Froling P2-10 Operating Instructions Manual Download

Page: 72 / 80

Installers and service technicians

Parameter list - Lambdatronic P 3100

Page 72

B0190806

Air settings ...

←

ID fan MIN

35%

←

Lower control limit; check during initial setup
Start from 0% and test going up in steps of 5%. . Start
level setting through control parameter,

→

ID fan start

point

Fan MIN

16%

←

Adjustment to fan in use – do not change setting

Fan MAX

65%

←

Fan speed at maximum output
Factory settings: P2-10: 60%, P2-15: 65%, P2-20:
70%, P2-25: 75%

100% output from

Flue gas temp.

100°

←

If the flue gas temperature is above the specified
target value, fuel output should reach 100% (upper
point of the start ramp)

Output at flue gas temp.
of 20°

50%

←

Output limit (lower point of the start ramp)

Offset for ID fan

←

The ID fan curve is increased by this value

New induced draft fan Y

←

ID fan with rubber buffer

→

ID fan with spacers

→

Pellets feed

...

←

Feed MAX

70%

←

Slide-in at maximum output for systems without
lambda probes; systems with lambda probes are
controlled by the O2 regulator.

STBY. Wait 1

10m

←

1. Shutdown pause before the 1st safety slide-in

STBY. Wait 2

20m

←

2. Pause between 1st and 2nd safety slide-in

Shutdown slide-in

←

Duration of safety slide-ins (for status: Shutdown slide-
in 1 and 2)

Ash screw Runtime:

←

Runtime of the ash screw

Ash screw Cycle:

1200

←

Ash screw cycle; control of the ash screw depending on
the pellet slide-in.

EOS runtime

20s

←

Runtime of heat exchanger cleaning

Outfeed

...

←

1. Start time for
automatic filling

15:00

←

1. Start time for filling. This is only carried out if the fill
level in the container is under 85%.

Only with suction
discharge unit!

2. Start time for
automatic filling

15:00

←

2. Start time for filling. This is also only carried out if
the fill level in the container is under 85%.

Period of screw
cycle

30s

←

Discharge screw runtime, minus a pause of 10* sec.
(*Pause time = “Suction unit pre-activation time”)

Preliminary suction

10s

←

Time before the discharge screw starts

ID fan after shut down

15s

←

Time after discharge screw stops.
For sucking the hose clear.

Fill cyclone below:

35%

←

Minimum level of day store

suction cycle starts when

the level falls below this value.

Note: with underground tanks or bag silos the values
for pre-activation and post-shutdown times should be
set according to the manufacturer’s instructions.

Summary of Contents for P2-10

















































































Search results

Summary of Contents for P2-10

Reviews:

Related manuals for P2-10

Brands by name

Popular brands

Froling P2-10, Operating Instructions Manual

Search results

Summary of Contents for P2-10

Reviews:

Related manuals for P2-10

Brands by name

Popular brands