Froling P2-10 Operating Instructions Manual Download Page 47

Page: 47 / 80

Troubleshooting

Fröling Heizkessel- und Behälterbau Ges.m.b.H, Industriestraße 12, A-4710 Grieskirchen, Austria

Page 47

Tel +43 (0) 7248 606-0 Fax +43 (0) 7248 606-600 [email protected] www.froeling.com

B0190806

Error text

Code Type

Cause of error

Error correction

Boiler remains in “IGNITE”
state longer than the
“Ignition time max”:

Acknowledge error

NOTE: After acknowledging the error, error correction starts
immediately. Keep the doors of the boiler closed!

After error correction starts, check if the induced draught fan is
running

CAUTION! In case of defective induced draught fan inform the
heating engineers or Fröling customer services!

When error correction has been automatically carried out (approx.
20 min) the warning, “Clean/ check burner”, is shown on the
display.

After you have done this, open the insulating door and
combustion chamber door

Clean embers, fuel and slag from the pellet burner (see
chapter on maintenance)

Clean the flue gas guide in the boiler up to the mouth of the
chimney

Empty the ash drawer if necessary

Acknowledge warning

Ignition failed

013

•

Too few pellets in
combustion bowl

•

Defective ignition

•

Stoker not feeding

Refill pellets in storage tank,
check discharge and stoker

ATTENTION! Do not feed any
pellets into the pellet burner
manually - danger of flash fires!

Have the ignition checked by
professionals

Check stoker drive

Summary of Contents for P2-10

















































































Search results

Summary of Contents for P2-10

Reviews:

Brands by name

Popular brands

Froling P2-10, Operating Instructions Manual

Search results

Summary of Contents for P2-10

Reviews:

Brands by name

Popular brands