Froling P2-10 Operating Instructions Manual Download Page 46

Page: 46 / 80

Troubleshooting

Page 46

B0190806

Error text

Code Type

Cause of error

Error correction

Oxygen content is greater
than the “Remaining O2 shut
down” parameter - duration
longer than safety time (in
the HEATING state):

Acknowledge error

NOTE: After acknowledging the error, error correction starts
immediately. Keep the doors of the boiler closed!

After error correction starts, check if the induced draught fan is
running

CAUTION! In case of defective induced draught fan inform the
heating engineers or Fröling customer services!

When error correction has been automatically carried out (approx.
20 min) the warning, “Clean/ check burner”, is shown on the
display.

After you have done this, open the insulating door and
combustion chamber door

Clean embers, fuel and slag from the pellet burner (see
chapter on maintenance)

Clean the flue gas guide in the boiler up to the mouth of the
chimney

Empty the ash drawer if necessary

Acknowledge warning

Safety time
O2 too high

039

•

Wrong air in boiler

•

Insufficient pellets fed
into combustion bowl

•

Bridge formation over
trough

•

Sensor incorrectly set

•

Stoker not feeding

Check seal on ash box and
front doors

Check seal on heat exchanger
cover

Check that lambda probe is
fitted firmly

Refill pellets in bunker, check
discharge and stoker

ATTENTION! Do not feed any
pellets into the pellet burner
manually - danger of flash fires!

Break up the bridge, check
pellet length

Readjust the sensor

Check stoker drive

Flow temp 1 false

002

•

Sensor signal damaged

Check sensor and sensor cable

Flow temp 2 false

003

•

Sensor signal damaged

Check sensor and sensor cable

Flow temp 3 false

023

•

Sensor signal damaged

Check sensor and sensor cable

Flow temp 4 false

024

•

Sensor signal damaged

Check sensor and sensor cable

Summary of Contents for P2-10

















































































Search results

Summary of Contents for P2-10

Reviews:

Brands by name

Popular brands

Froling P2-10, Operating Instructions Manual

Search results

Summary of Contents for P2-10

Reviews:

Brands by name

Popular brands