Froling P2-10 Operating Instructions Manual Download

Page: 76 / 80

Installers and service technicians

Parameter list - Lambdatronic P 3100

Page 76

B0190806

7.5.6

Manual anal. menu OUT

Used to test the digital outputs and is intended only for heating
engineers. The display depends on the configuration.

ID fan

A 0%

←

Storage tank LPA 0%

Storage tank loading pump

DHW LP A 0%

←

DHW tank loading pump

Pump 1 A 0%

←

Pump 2 A 0%

←

Pump 3 A 0%

←

Comb air fanA 0%

Supply air fan

Stoker

A 0%

←

Function check is also possible in “Manual control” menu

Discharge
screw

A 0%

←

Function check is also possible in “Manual control” menu

HCP 1

A 0%

←

Collector pump for solar systems (if available)

A 0%...

Automatic, OFF

A 1%-100%...

Automatic, corresponding value ON

A...

AUTOMATIC

0%...

Manual OFF

1%-100%...

anual with corresponding value ON

7.5.7

Manual digi.menu IN

Used to test the digital inputs and is intended only for heating
engineers. The display depends on the configuration.

Door sensor A 0

←

Limit thermostat
emergency off A 1

←

Safety temperature limiter / EMERGENCY STOP

Jam sensor A 0

←

“Jam sensor” for suction feed “Gravity shaft level sensor”
for screw discharge

Level MIN

A 0

←

Input not covered

Level MAX

A 1

←

Only for suction feed: Maximum for day store ends suction
cycles.

Com.Ch. exc.
press.

A 1

←

Combustion chamber excess pressure monitor: “Opener”

Ext. req.

A 0

←

For external heat requirements, e.g. from a house control
system input “S6 boiler release” in pellet module

A 0…

Automatic, OFF

A…

AUTOMATIC

A 1...

Automatic, ON

0...

Manual OFF

1…

Manual ON

Summary of Contents for P2-10

















































































Search results

Summary of Contents for P2-10

Reviews:

Related manuals for P2-10

Brands by name

Popular brands

Froling P2-10, Operating Instructions Manual

Search results

Summary of Contents for P2-10

Reviews:

Related manuals for P2-10

Brands by name

Popular brands