Froling P2-10 Operating Instructions Manual Download Page 5

Page: 5 / 80

Contents

Fröling Heizkessel- und Behälterbau Ges.m.b.H, Industriestraße 12, A-4710 Grieskirchen, Austria

Page 5

Tel +43 (0) 7248 606-0 Fax +43 (0) 7248 606-600 [email protected] www.froeling.com

B0190806

Installers and service technicians

7.1

Connection layout of the boards

7.2

Connection instructions

7.2.1

Mains connection ............................................................................................. 50

7.2.2

Heating circuit pumps for floor or wall heating..................................................... 50

7.2.3

Jumper setting for solar control ......................................................................... 51

7.2.4

Flue gas sensor ............................................................................................... 51

7.2.5

Remote control ................................................................................................ 51

7.2.6

RBG 3100 room console ................................................................................... 52

7.2.7

PC Visualisation ............................................................................................... 52

7.2.8

Heating circuit pump 0 / Oil - oil burner contact .................................................. 53

7.3

Connection layout of the pellet module

7.3.1

Pellet module with ash discharge ....................................................................... 54

7.3.2

Pellet module with suction system ..................................................................... 55

7.3.3

Overview of connected components ................................................................... 56

7.3.4

Connection instructions for Komfort pellet box..................................................... 57

7.3.5

Boiler Release ................................................................................................. 58

7.4

Initial startup

7.4.1

Turn on system ............................................................................................... 59

7.4.2

Changing operating level .................................................................................. 59

7.4.3

Setting system type ......................................................................................... 60

Boiler types and parameters............................................................................. 60

System .......................................................................................................... 61

7.4.4

Checks before first heating up ........................................................................... 62

Heating system............................................................................................... 62

Drives ........................................................................................................... 63

Sensors ......................................................................................................... 63

Setting sensor “Level Max”............................................................................... 64

7.4.5

Feeding fuel into the combustion chamber .......................................................... 64

7.4.6

Setting parameters .......................................................................................... 65

7.5

Lambdatronic P 3100 parameter list

7.5.1

Menu overview ................................................................................................ 66

7.5.2

Settings menu ................................................................................................. 67

7.5.3

Error list menu ................................................................................................ 74

7.5.4

Manual operation menu .................................................................................... 75

7.5.5

Manual digi.menu OUT ..................................................................................... 75

7.5.6

Manual anal. menu OUT.................................................................................... 76

7.5.7

Manual digi.menu IN ........................................................................................ 76

Appendix

8.1

Guarantee conditions

8.2

Manufacturer address

8.3

Declaration of Conformity

Your Notes

Summary of Contents for P2-10

















































































Search results

Summary of Contents for P2-10

Reviews:

Related manuals for P2-10

Brands by name

Popular brands

Froling P2-10, Operating Instructions Manual

Search results

Summary of Contents for P2-10

Reviews:

Related manuals for P2-10

Brands by name

Popular brands