Froling P2-10 Operating Instructions Manual Download Page 53

Page: 53 / 80

Installers and service technicians

Electrical Connection

Fröling Heizkessel- und Behälterbau Ges.m.b.H, Industriestraße 12, A-4710 Grieskirchen, Austria

Page 53

Tel +43 (0) 7248 606-0 Fax +43 (0) 7248 606-600 [email protected] www.froeling.com

B0190806

7.2.8

Heating circuit pump 0 / Oil - oil burner contact

The HCP 0 / oil connection can be used either for heating circuit pump 0
or as an burner relay depending on the system settings.

Connecting a HCP 0 up to 2 Ampere:

Connecting a HCP 0 up to 5 Ampere:

External power supply

Connection as an burner relay:

NOTE

Always set the pumps to the highest power level.

always set the pump to the highest power level.

LV

N

Lambdatronic

P 3100

HCP 0

LV

N

to oil boiler controls:
floating contact for
burner release

Lambdatronic

P 3100

LV

N

Lambdatronic

P 3100

HCP 0

P
E

Summary of Contents for P2-10

















































































Search results

Summary of Contents for P2-10

Reviews:

Brands by name

Popular brands

Froling P2-10, Operating Instructions Manual

Search results

Summary of Contents for P2-10

Reviews:

Brands by name

Popular brands