manualshive.com logo in svg

Froling P2-10, Operating Instructions Manual

Share
Download
Froling P2-10 Operating Instructions Manual Download Page 64

Installers and service technicians 

Initial startup 

 

 
Page 64 

B0190806

 

s 

7 

Setting sensor “Level Max” 

In delivery configuration, the factory settings of 
the sensor are secured with a seal.  
Changes to the settings should only be carried out 
by qualified technicians. 

 

 

The monitoring LED (1) should only illuminate 
when identifying materials! 

 

 

If the monitoring LED is constantly lit, the 
sensitivity is set too high! 

 

Reduce the sensitivity by turning the 
adjusting screw (2) to the left 

 

 

If the monitoring LED does not react when 
pellets are being fed in, the sensitivity is set 
too low! 

 

Increase the sensitivity of the adjusting 
screw by turning to the right 

 

 

 

7.4.5

 

Feeding fuel into the combustion chamber 

Before the initial setup there are no pellets in the stoker and discharge 
screw. With the “Manual fuel” parameter, pellets are fed into the 
combustion chamber.  

 

 

MANUAL FUEL 

ON

←

←

←

←

 

If the first pellets are visible in the combustion bowl, 
set the “Manual fuel” parameter back to “OFF”.  

 

 

CAUTION: Placing too many pellets in the combustion bowl 
can increase the danger of flash fires! 

 

 

Combustion bowl correctly 
filled 

 

 

Too many pellets in the 
combustion bowl 

 

 

 

 

 

1 

2 

Summary of Contents for P2-10

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands