Froling P2-10 Operating Instructions Manual Download | Manualshive

Page: 26 / 80

background image

Lambdatronic P 3100 control system

Display messages

Page 26

B0190806

s

4

4.2.2

Operating statuses

Preparation

The induced draught fan is switched on.

Heating up

The combustion bowl is filled with pellets. The supply air fan, the induced
draught fan and the igniter are turned on.

Pre-heating

The pellets are pre-warmed with the fan-assisted ignition and a bed of embers
is formed. No fuel slide-in unit.

Ignition

The pellets are ignited with the fan-assisted ignition. The flame is spread across
the whole combustion bowl. The supply air fan, the ID fan, and the slide-in unit
can be set in the “Ignition” menu.

Heating

The Lambdatronic controls combustion according to the target boiler values.

Constant burn

The boiler has reached the specified temperature and there is no reduction in
temperature. The supply air fan, the ID fan, and the slide-in unit are
deactivated.

STBY. Wait 1

The supply air fan and perhaps the ID fan are running too slowly (“Fan during
shut down”) to burn the remaining pellets. No slide-in.

STBY. Feed 1

Safety slide-in after the first wait time. As with status “STBY. Wait 1”, but
with slide-in, in accordance with the parameter, “Feed off”.

STBY. Wait 2

The supply air blower fan and the induced draught are switched off, no slide-in.

STBY. Feed 2

Safety slide-in after the second wait time. As with status “STBY. Wait 2”, but
with slide-in, in accordance with the parameter, “Feed off”.

Fault

ATTENTION - Fault!

Error correction 20 min

When the faults “Ignition failed”, “Safety time elapsed too low”, “Safety time
O2 too high” and “Pressure monitor comb chamb” are acknowledged, error
correction starts. When error correction has been carried out (approx. 20 min)
the warning, “Clean/ check burner”, is shown on the display. The warning can
only be acknowledged with the enter key after checking the burner.

Burner Off

This status is reached by pressing the

key when store or DHW tank loading

has finished, or after acknowledging an error message, which requires a
shutdown. All parts of the boiler stop. The system now only regulates the
connected heating components.

«
...
24
25
26
27
28
...
»

Summary of Contents for P2-10

















































































Reviews:

No comments

Related manuals for P2-10

Brand: HURAKAN Pages: 22

Brand: Nibe Pages: 32

Brand: Dunkirk Pages: 32

Brand: Baxi Pages: 16

Brand: Vaillant Pages: 52

Brand: Ideal Boilers Pages: 8

Ethos 28 Series

Brand: Mikrofill Pages: 66

Brand: Strebel Pages: 30

MT. OLYMPUS WS-SFR

Brand: Wood Stone Pages: 21

Brand: CAC / BDP Pages: 32

Brand: Potterton Pages: 40

Mexico Super FF4100

Brand: Ideal Boilers Pages: 44

Brand: Bryan Boilers Pages: 2

Brand: Bryan Boilers Pages: 2

Brand: Ideal Boilers Pages: 4

Brand: Potterton Pages: 8

Brand: Rinnai Pages: 22

Brand: Redring Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands