Fri-Jado MCC 120 Service Manual Download Page 8

Page: 8 / 105

Page 8

Service Manual MCC Cold US 20220700

1.4.3 Cold units with remote CO2 (R744) refrigerant

WARNING

Remote R744 refrigerant is environmentally friendly but under high pressure. It is non-toxic

with zero Ozone Depletion Potential (ODP) and very low Global Warming Potential (GWP).

Read the user manual carefully and follow all precautions described herein.

SAFETY

Wear eye protection when working on the refrigeration system.

•

Do not tamper with the system.

•

The system must be installed and maintained by qualified persons only.

•

Fixate the unit to the floor.

•

The ventilation openings of the cladding of the unit (including accessories) must not

be blocked or covered.

Ensure that the air circulation remain unobstructed.

Summary of Contents for MCC 120










































































































Search results

Summary of Contents for MCC 120

Reviews:

Related manuals for MCC 120

Brands by name

Popular brands

Fri-Jado MCC 120, Service Manual

Search results

Summary of Contents for MCC 120

Reviews:

Related manuals for MCC 120

Brands by name

Popular brands