Fri-Jado MCC 120 Service Manual Download Page 55

Page: 55 / 105

Service Manual MCC Cold US 20220700

Page 55

8.0

Maintenance

CLEANING AND MAINTENANCE

WARNING

Never use a water hose for cleaning.

Water can seep into the unit through the ventilation holes of the unit.

Because of hygiene aspects and optimum condition of the unit it is of up most importance to keep a

daily cleaning pattern from first use onwards.

Maintenance schedule for users

For detailed cleaning instructions refer to User manual chapter 5

Examples:

Cleaning possibility the top glass pane all units

Cleaning possibility side pane all units

Cleaning possibility off the top air guides

Item

Action

Frequency

Inside

Clean

Daily

Glass Panes

Clean

Weekly

Outside

Clean

Use Stainless Steel cleaning spray to remove stains,

and restoring the gloss.

Weekly

Condenser

Clean

Monthly

Summary of Contents for MCC 120










































































































Search results

Summary of Contents for MCC 120

Reviews:

Related manuals for MCC 120

Brands by name

Popular brands

Fri-Jado MCC 120, Service Manual

Search results

Summary of Contents for MCC 120

Reviews:

Related manuals for MCC 120

Brands by name

Popular brands